Jeep 200 Cherokee, Руководство по обслуживанию

Страница: 462 / 2119

wipe cycle when the windshield wiper switch stalk is
moved to the Off position, and parks the blades in
the lowest portion of the wipe pattern.
The windshield wiper motor cannot be repaired. If
faulty or damaged, the entire wiper linkage and pivot
module unit must be replaced. The reinforcement
bracket and stud plate are available for service.
REAR
The rear wiper motor is secured to a bracket that
is fastened to the liftgate inner panel, below the lift-
gate glass and behind the liftgate trim panel. The
motor output shaft passes through the liftgate outer
panel where a rubber gasket and plastic bezel unit,
and a nut seal and secure the unit to the liftgate
outer panel. The rear wiper arm is secured directly
to the motor output shaft with a nut.
The rear wiper motor unit provides three operating
modes:
•
Constant wipe that operates when the rear
wiper switch is turned to the On position.
•
Constant wipe that operates when the rear
washer switch is depressed.
•
A park mode that operates the wiper motor until
the blade reaches its park position when either the
rear wiper switch or the ignition switch is placed in
the Off position.
The rear wiper motor cannot be repaired. If faulty
or damaged, the entire rear wiper motor assembly
must be replaced.
WIPER SWITCH AND WASHER SWITCH
FRONT
The windshield wiper and washer switches are
mounted on the right side of the steering column
(Fig. 1). The switch stalk is moved up or down to
select the wiper switch mode, and pulled towards the
steering wheel to activate the washer system. An
intermittent wipe system control knob on the end of
the switch stalk is rotated to select the desired delay
interval. The windshield wiper and washer switch
contains circuitry for the following functions:
•
Windshield wipers
•
Intermittent wiper delay relay control and logic
•
Intermittent wipe relay
•
Windshield washers.
The windshield wiper and washer switch cannot be
repaired. If any function of the switch is faulty, or if
the switch is damaged, the entire switch unit must
be replaced.
REAR
The single two-function rear wiper and washer
switch is installed in the instrument panel accessory
switch bezel, which is located near the bottom of the
instrument panel center bezel area, below the heater
and air conditioner controls. The rear wiper and
washer switch controls the rear wiper and washer
functions.
The toggle-type switch features a detent in the On
position, and a momentary Wash position. The rear
wiper and washer switch also has an integral illumi-
nation lamp with a serviceable bulb. The switch knob
is pushed down to its detent to activate the rear
wiper system, and down again to the momentary
position to activate the rear washer system. Both the
rear wiper and rear washer motors will operate con-
tinuously for as long as the switch is held in the
momentary Wash position.
The rear wiper and washer switch cannot be
repaired and, if faulty or damaged, the entire switch
unit must be replaced.
WASHER RESERVOIR
A single washer fluid reservoir is used for both the
standard front and optional rear washer systems.
The washer fluid reservoir is secured between the
left front inner and outer fender panels, above and in
front of the left front wheel house.
Each washer pump and motor unit has a barbed
nipple, which is installed through a rubber grommet
seal inserted in a hole near the bottom of the reser-
voir. The washer pumps are retained by an interfer-
ence fit between the barbed nipple and the grommet
seal, which is a light press fit.
The washer reservoir has a separate filler neck
and grommet seal. The filler neck snaps into the res-
ervoir from the engine compartment side of the left
inner fender shield. A snap-fit filler cap with an inte-
gral bail strap is fit to the reservoir filler neck. On
models so equipped, the reservoir also has a hole pro-
vided for a washer fluid level sensor.
The washer reservoir, filler neck, grommet seal,
and filler cap are each available for service.
Fig. 1 Windshield Wiper Switch and Washer Switch
XJ
WIPER AND WASHER SYSTEMS 8K - 3
DESCRIPTION AND OPERATION (Continued)