JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 500 | Manualshive

Страница: 500 / 592

JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 500

JD780A Series Analyzers

500

Using Cable and Antenna Analyzer

Connecting a cable

Connecting a cable for reflection, DTF, 1-port phase, and Smith
Chart measurements

Procedure

1.

Connect the one end of the port extension cable to the

Cable and Antenna Analyzer

Reflection/RF Out

port of the instrument.

2.

Connect the other end of the port extension cable to an antenna or feed line as illustrated in
Figure 251.

Measurement result is displayed on the screen.

Figure 251

Connection for reflection measurement

NOTE

After calibration, do not change the connection of the port extension cable or the
frequency setting. It may cause a measurement error.

Changing any frequency settings will automatically turn the calibration status to OFF on
the display screen, which requires re-calibration to proceed next measurement.

CAUTION

The maximum input power for the

Cable and Antenna Analyzer Reflection/RF Out

port

is +25 dBm. Do not connect this port directly to the output port of the system to prevent
degraded performance or malfunctioning.

WARNING

Do not attempt to connect the instrument to the antenna when there is a risk of lightning.
Electric shock may cause malfunction of or damage to the instrument.

Connecting a cable for cable loss (1 port) measurements

Procedure

1.

Connect the one end of the cable under test to the

Cable and Antenna Analyzer Reflection/RF

«
...
498
499
500
501
502
...
»

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды