JCM TBV Series Скачать руководство пользователя

Страница: 28 / 40

Part No. 960-100941R_Rev. A

2 8

October, 2016

JCM® Training Overview

TBV Transaction Based Validator

Pusher

Mechanism

Movement

The Pusher Mechanism is not at the Home Sensor.

[Solution] Check for a jammed Banknote or foreign material. Clean the Unit.

[Relative Parts] Pusher Mechanism, Stacker Motor, Stacker Home Sensor,
Stacker Motor Encoder

If the condition is not resolved, change the above related part or parts.

Pusher

Mechanism

Home Position

When stacking a Banknote, the Pusher Mechanism is not returning to the
Home Position.

[Solution] Check for a jammed Banknote or foreign material. Clean the Unit.

[Relative Parts] Pusher Mechanism, Stacker Motor, Stacker Home Sensor,
Stacker Motor Encoder

If the condition is not resolved, change the above related part or parts.

Pusher Halfway

Position

The Pusher Mechanism is not returning to the Halfway Position.

[Solution] Check for a jammed Banknote or foreign material. Clean the Unit.

[Relative Parts] Pusher Mechanism, Stacker Motor, Stacker Home Sensor,
Stacker Motor Encoder

If the condition is not resolved, change the above related part or parts.

Center

Home Position

The Centering Mechanism is not at the Home Position.

[Solution] Check for a jammed Banknote or foreign material. Clean the Unit.

[Relative Parts] Centering Motor, Centering Guide, Centering Home Sensor

If the condition is not resolved, change the above related part or parts.

Feed Motor

Speed

During initialization, the Feed Motor Speed is incorrect.

[Solution] Check the following Parts and Harnesses. Clean the Unit.

[Relative Parts] Feed Motor, Feed Motor Encoder

If the condition is not resolved, change the above related part or parts.

BNF Section

Communication

The BNF Unit is not communicating with the CPU.

[Solution] Check the BNF Harnesses.

[Relative Part] BNF Communications Harness

If the condition is not resolved, change the above related part.

ICB

Communications

(1)

During ICB Communication, Data Errors are occurring.

[Solution] Check ICB Settings and reseat the Cash Box. Clean the Unit.

[Relative Part] ICB PC Board

If the condition is not resolved, change the above related part.

Voltage

Input voltage is too low.

[Solution] Check the Harness and the following part.

[Relative Part] Power Supply

If the condition is not resolved, change the above related part.

Banknote Timing

Sensors detected a Banknote with abnormal timing.

[Solution] Clean the Transport Path, check the following parts.

[Relative Parts] Line Sensor, Feed-Out Sensor, Box Feed Out Sensor, Side
Sensor

If the condition is not resolved, change the above related part or parts and
calibrate the Unit.

I2C Access

While communicating with each device connected to the CPU, Sensors
detected an abnormality.

[Solution] Check the Harness connections and the following part.

[Relative Parts] CPU Board

If the condition is not resolved, change the above related part and calibrate
the Unit.

Table 14

TBV Operational Error Codes (Continued)

LED Color

Flash

Sequence

Error

Causes and Solutions

Содержание TBV Series









































Результаты поиска

Содержание TBV Series

Отзывы:

Похожие инструкции для TBV Series

Бренды по названию

Популярные бренды

JCM TBV Series, Тренировка

Результаты поиска

Содержание TBV Series

Отзывы:

Похожие инструкции для TBV Series

Бренды по названию

Популярные бренды