P/N 960-100175R_Rev. 4 {EDP #200824}
© 2013, Japan CashMachine Co., Limited
2 - 5
Installation
Taiko™ Series Banknote Acceptor
Section 2
Encryption Code Initialization Setting
Mode
When using the ccTalk Communication Mode (e.g.,
The Encryption Mode) and the Encryption Code is
unknown, set the Encryption Code Initialization
Setting to start the Encryption Code in order to
identify the last 6 Digits of the specific Taiko™
Serial Number located on the back side of a
Taiko™ Unit.
To set the “Encryption Mode” operating function,
perform the following steps:
1. Remove Power from the Taiko™ Unit.
2. Set DIP Switch No.1 through No.6 to
ON
, and
Switches No.7 and No.8 to
OFF
16).
3. Re-apply Power to the Taiko™ Unit.
4. Set DIP Switch No.1 to
OFF
to initialize the
Encryption Code setting.
The Taiko™ installation DIP Switch settings are
now complete.
Error Codes & Conditions
Table 2-4 lists the
Red
Error Code flash sequence
definitions displayed by the Taiko™ Front Panel
LED indicator.
Interface Connector Pin
Assignments
Table 2-5, Table 2-6, Table 2-7 and Table 2-8 list
the various Connector Pin Labels for adapting these
available Communication Standards to the Unit.
Table 2-4
Red LED Error Code Flash Definitions
Red
Flashes
Error Indicated
2
ROM Error
3
Banknote Jam inside Ejection Slot
4
Banknote remains inside on the Transport Path
5
EEPROM Read/Write Error
6
Motor Error
8
Entrance Solenoid Error
9
Exit Solenoid Error
12
Sensor Operation with Abnormal Timing
Figure 2-16
Encryption Mode DIP Switch Settings
ON
Figure 2-17
ID-003/MDB/Pulse Interface
Connector
Internal 10-Pin S10B-PADSS-1 (JST)
Table 2-5
Serial ID-003/MDB Interface Pin
Assignments
Pin No.
Signal
Name
I/O
*
*. I/O (Input/Output) is the function viewed from the Banknote Acceptor
Side.
Function
1
NC
-
No Connection
2
NC
-
No Connection
3
RXD-
IN
Data Receive Line
(Active when current is present)
4
RXD+
5
TXD-
OUT
Data Send Line
(Active when current is present)
6
TXD+
7
Vcc
-
+12V DC Power (7-Pin)
8
Vss
-
Power Ground
9
Vcc
-
+24V DC Power (9-Pin)
†
†. 24V DC is available only when the optional 24V DC Specification is
used.
10
NC
-
No Connection
Table 2-6
ccTalk Interface Pin Assignments
Pin No.
Signal
Name
I/O
*
*. I/O (Input/Output) is the function viewed from the Banknote Acceptor
Side.
Function
1
ccTalk
IN/OUT ccTalk Send/Receive Line
2
ccTalk
-
ccTalk GND Line
3
NC
-
No Connection
4
NC
-
No Connection
5
NC
-
No Connection
6
NC
-
No Connection
7
Vcc
-
+12V DC Power (7-Pin)
8
Vss
-
Power Ground
9
Vcc
-
+24V DC Power (9-Pin)
†
†. 24V DC is available only when the optional 24V DC Specification is
used.
10
NC
-
No Connection
Table 2-7
Pulse Interface Pin Assignments
Pin No.
Signal
Name
I/O
*
*. I/O (Input/Output) is the function viewed from the Banknote Acceptor
Side.
Function
1
NC
-
No Connection
2
NC
-
No Connection
3
Enable/
Disable (-)
IN
-
Enable/Disable Signal Input Line
(Enabled when current is present)
(Disabled when current is present)
No Connection
4
Enable/
Disable (+)
5
Vend (-)
OUT
Pulse Signal Output Line
(Active when current is present)
6
Vend (+)
7
Vcc
-
+12V DC Power (7-Pin)
8
Vss
-
Power Ground
9
Vcc
-
+24V DC Power (9-Pin)
†
†. 24V DC is available only when the optional 24V DC Specification is
used.
10
NC
-
No Connection
Figure 2-18
ID-001 Interface Connector
Internal 16-Pin S16B-PADSS-1 (JST)
