JCM TAIKO PUB-7/11 Скачать руководство пользователя страница 26

Страница: 26 / 84

P/N 960-100175R_Rev. 4 {EDP #200824}

2 - 2

Section 2

Taiko™ Series Banknote Acceptor

Installation

9. Open the Upper Lid by pressing-in and holding

down the Upper Lid Open/Close Buttons while

lifting the Lid up (See Figure 2-6



10. Insert the Bezel Installation Guide Pin into the

Bezel Guide (See Figure 2-6



11. Slide the Guide all the way in and push down on

the Taiko™ Unit body (See Figure 2-6



12. Close the Upper Lid firmly until a locking Click

is heard (See Figure 2-7).

Power Harness Wiring Procedure

Before beginning to build a Power Interface



Connector, ensure one of the two plug types listed

in Table 2-1 are available.

Once the Power Interface Connector Plug has been

fastened to the Power/Signal Cable being used,



perform the following steps:

1. Confirm the power is NOT supplied to the new

Power Harness.

2. Insert the new Power Harness Socket into the

right side Panel Interface Connector of the

Taiko™ Unit Body (See Figure 2-8).

3. Supply power and confirm that the Taiko™ Unit

operates properly.

Clearing a Banknote Jam

Clearing an Upper Area Banknote Jam

When an upper area Banknote jam occurs, the

Front Panel

Red

LED Display will begin blinking

three (3) time with a pause between blink sets.



Perform the following steps to clear a Banknote

jam within the Taiko™ Unit’s Acceptor area:

1. Remove Power from the Taiko™ Unit.

Figure 2-5

Mounting the Taiko Bezel

Bezel Brackets

Hexagonal
Nuts

Figure 2-6

Installing the Taiko Bezel







Figure 2-7

Closing the Taiko Upper Lid

Click

Caution: Ensure that the Taiko Unit body
and Bezel are firmly installed and stably
fixed to the door before closing the
Upper Lid; When closing the Upper Lid,
be careful not to get your finger caught
under the lid when pressing it closed.

NOTE: When removing a Taiko Unit, perform the
reverse procedure as previously described.

Table 2-1

Power Connector Specifications

Part

Connector

Lock Lever Socket

Ribbon Cable Socket

Plug

XG5M-1032-N

(Omron)

XG4M-1030-T

(Omron)

Semi-Cover

XG5X-0501 (Omron)

N/A

Lock Lever 2 XG4Z-0002 (Omron)

N/A

Applicable

Wire Size

UL1061 WAG24

1.27mm Pitch Flat

Ribbon Cable, AWG28

UL2651 or UL20012

NOTE: DIP Switch settings may vary based on
Software changes related to the specific Country
using the Taiko Unit.

Figure 2-8

Attaching a Taiko Power Connector

WARNING: When installing a Taiko Unit,
or connecting its Harness Plug, be sure
power to the harness is disconnected.



The Taiko Unit is only designed to use a
12 Volt DC input. Any other power level
can damage the Taiko Unit!



If the power Harness itself is strongly
pulled on, it may tear loose from its
Connector’s Pins.

Содержание TAIKO PUB-7/11





















































































Результаты поиска

Содержание TAIKO PUB-7/11

Отзывы:

Похожие инструкции для TAIKO PUB-7/11

Бренды по названию

Популярные бренды

JCM TAIKO PUB-7/11, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TAIKO PUB-7/11

Отзывы:

Похожие инструкции для TAIKO PUB-7/11

Бренды по названию

Популярные бренды