P/N 960-100175R_Rev. 4 {EDP #200824}
© 2013, Japan CashMachine Co., Limited
1 - 2
Section 1
Taiko™ Series Banknote Acceptor
General Information
Model Descriptions
Table 1-1 lists the Product Model Number
Descriptions.
Precautions
The Figure 1-2 symbols are defined as follows:
1. (
Type 1
) Do not insert a torn, folded, or wet
Banknote, as this action may cause a Banknote
jam inside the unit.
2. (
Type 2
) Do not expose the unit to water. The unit
contains several precision electronic devices
which can be damaged if water or any liquid is
sprayed or spilled into the unit.
3. (
Type 3
) Do not install the unit into a dusty
environment. Dust may affect and degrade the
sensor’s performance.
U
SER
C
AUTIONS
Careful measures are taken in this product to
ensure its quality; however, the following cautions
should be read and understood by all users in order
to confirm safe operation.
Installation Cautions
The Installation Cautions are defined as follows:
1. Do not allow the Unit to endure or operate at a
high temperature, in high humidity and/or in a
dusty environment.
2. Do not use the Acceptor where temperature vari-
ations widely fluctuate.
3. Do not install the Unit into an area where exces-
sive vibration, shock or chemical vapors are pres-
ent.
4. This equipment is intended for indoor use only.
Be sure that the Host Machine contains enough
protection to avoid wet or dusty conditions when
installing.
5. Avoid exposing the Unit to direct Sunlight and/or
incandescent Lamp illumination having a Gradi-
ent Angle of 15 Degree or more, and an illumina-
tion index of 3,000 Lux or less.
6. Insure that the Host Machine is designed for
daily operational access such as maintenance
and/or cleaning a Banknote Jam.
7. Be sure to use in the specified power range and
pin assignment. If not, the Unit may be damaged.
8. Be sure to connect the power harness connectors
firmly, otherwise an incorrect input/output con-
tact failure may occur.
9. Do not pull on the power harness to disconnect
its connector or damage may occur.
10. Do not obstruct the Acceptor’s air holes in order
to provide sufficient cooling to the Unit.
Mounting, Dismounting & Transportation
Methods for Mounting, Dismounting & Transport-
ing the Unit are as follows:
1. Be sure to turn the Power OFF before mounting
or removing the Unit from its permanent loca-
tion. Plugging or unplugging Connector Plugs
from their receptacles while the Power is ON
may cause damage to the Unit.
2. When reassembling a disassembled Unit Section,
ensure that each part is properly placed in its
correct location.
3. Be sure to carry the Unit by both hands when
transporting it. Holding the Unit by one hand
may cause personal injury if the Unit accidently
becomes disassembled and falls apart.
4. Be careful not to use excessive outside pressure
on the Unit, or subject it to excessive vibration
during transportation.
5. Do not throw or pound hard on the Unit.
Preventive Maintenance
The Preventive Maintenance requirements are
defined as follows:
1. Be sure the Power to the Unit is OFF before
beginning a Maintenance Procedure. The equip-
ment produces improper operating signals while
in maintenance mode that may cause personal
injury.
2. Be sure to remove power to the Unit when open-
ing the upper or lower lid. The active Roller may
cause personal injury.
Table 1-1
Taiko PUB-7/11 Model Number
Specifications
N
o
Model: PUB
-
*
-
***
-
*
-
*
-
*
-
*
-
**
N
o
(1) (2) (3) (4) (5) (6) (7)
(1) Validation Method
7 = Optical/Transmissive/Reflection
11 = Optical/Transmissive/Reflection/Magnetic (MAG)
(2) Country Code
Type - ISO 3116 based 3-digit codes
(3)
Bezel
0 = No Bezel
1 = Banknote Width Minimum = 67mm/Maximum = 82mm (Euro)
2 = Banknote Width Minimum = 75mm/Maximum = 82mm (British)
3 = Banknote Width Minimum = 70mm/Maximum = 82mm (China/Taiwan)
5 = Banknote Width Minimum = 66mm (US Dollar)
(4)
Optional Unit
0 = Without Optional Unit
1 = With Optional Interface Pin Assignment Conversion Adaptor
Harness Unit (ccTalk Compatible)
2 = Parallel (ID-001) Interface Type (Upper Tray dedicated 16-Pin
Connector)
3 = Individual Specification
4 = 24V DC Specification
5 = Barcode Coupon Specification
(5)
CPU Board Type
0 = Standard
2 = Interface Pin Assignment (ccTalk Compatible)
3 = Parallel Interface
4 = 24V DC/12V DC
*
*. 24V DC is only available when using the Optional 24V DC Version.
(6)
Optional Code
0 = Standard
1 = Individual Specification
(7)
Interface
X4 = ID-003 (Serial)/MDB/Pulse/ccTalk
01 = ID-001 (Parallel)
03 = ID-003 (Serial) (For Barcode Specification)
62 = ID-062
Type 1
Type 2
Type 3
Figure 1-2
Precautionary Symbols
