manualshive.com logo in svg

JCM ivizion ld, Эксплуатация и обслуживание

Поделиться
Скачать
JCM ivizion ld Скачать руководство пользователя страница 83

P/N 960-100929R_Rev. 7 {EDP #148849}

© 2017, JAPAN CASH MACHINE CO., LTD.

6 - 1 1

Calibration and Testing

iVIZION® SeriesNext-Generation Banknote Acceptor Unit

Section 6

Performance Tests

This portion explains the iVIZION Performance 

Test Procedures. The following two (2) methods 

exist to perform this Performance Test Procedure.

•  

Performance Test using a PC

•  

Performance Test using the External DIP Switches.

Choose one (1) of the two (2) above Performance 

Test Procedures by selecting the one related to the 

particular circumstance desired.

:

Performance Test Items using a PC

Table 6-2 lists the available Performance Test Items 

and their purpose using a PC for testing.

PC Performance Test Preparation

Perform following steps to begin the Performance 

Test Preparation Procedure:

1.  Turn the iVIZION Unit’s Power Switch 

OFF

.

2.  Remove the Transport Unit from the Frame.
3.  Set 8-Position DIP Switch #8 to 

ON

.

4.  Place the Transport Unit into the Frame.
5.  Turn the iVIZION Unit’s Power Switch 

ON

. 

The Status LED will light a steady 

Blue

 Color.

6.  Launch the “

JCM Tool Suite Standard Edition

” 

Application. The Screen shown in Figure 6-52 
will appear when the application becomes active.

7.  Click on, and hold-down the “Service Mode” 

selection

 Pull-Down Menu

 (Figure 6-52 

a

) and 

Slide-down select “

Performance Test

” from the 

Pull-Down Menu Selections (Figure 6-52 

b

). 

8. Activate 

the 

“

iVIZION Test Item VerX.XX

” Appli-

cation and the Screen shown in Figure 6-53 will 

automatically appear. 

Table 6-2 

PC Performance Test Items

No.

Test Item

Test Purpose

Status LED

Stand

-by

Operating

1

Motor 

Normal 

Rotation

Testing the Transport 

Motor rotation in a 

Banknote intake 

direction

Blue

Lit

Yellow 

Flashes

2

Motor

Reverse 

Rotation

Testing the Transport 

Motor rotation in a 

Banknote reject 

direction

3

Stacker 

Motor

Testing the Stacker 

Motor’s movement

4

Cycle 

Movement

Testing sequential 

movement from 

Banknote trans-

portation to stacking 

at regular intervals 

without Banknotes

5

Status LED 

Indication

Testing the Status 

LED Indications

Red

Green

Blue

6

Sensor ON/

OFF

Testing each 

Sensor’s 

Performance

Blue

Lit

Blue

Lit

7

DIP Switch 

ON/OFF

Testing the 8-Position 

DIP Switches 

Performance

8

Banknote 

Acceptance

Testing 

Transportation, 

Validation, Stacking 

and Reject 

Performance, and the 

Vend Signal Output

Extinguished

(Out)

9

ICB Setting

(Reading 

Ticket)

Setting the ICB 

Enable, Disable and 

Machine No. 

Functions.

NOTE: Refer to Figure 6-1 and Figure 6-2 

for the necessary Tools and Harness 

Connections and USB Cable Type 

Requirements respectively.

Figure 6-51 

DIP Switch #8 Set ON

Figure 6-51 

DIP Switch #8 Set ON

Figure 6-52 

JCM Tool Suite Standard Edition 

Screen

Figure 6-52 

JCM Tool Suite Standard Edition 
Screen

a

b

Figure 6-53 

iVIZION Test Item VerX.XX Screen

Figure 6-53 

iVIZION Test Item VerX.XX Screen

a

b

c

d

f

i

g

h

e

Содержание ivizion ld































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды