background image

 P/N 960-000173R_Rev. A {EDP #229278}

 © 2013, JAPAN CASH MACHINE CO., LTD.

1 8

 EBA

®

 Series Banknote Acceptor (EBA-40) Integration Guide

Retrieving Banknotes

To retrieve Cash Box deposited Banknotes, perform 

the following steps:

1.  Unlock the Stacker Box lock using the supplied 

Coin Key (See Figure 14 

a

).

2.  Pull the Stacker Box out of the Frame Housing 

(See Figure 14 

b

) and retrieve the Banknotes.

Clearing a Banknote Jam

To retrieve a jammed Banknote located inside the 

Banknote Acceptor, proceed as follows:

1.  Pull the Tabs (See Figure 15 

a

) located on the 

both sides of the Acceptor Assembly to open the 

Unit’s Front Cover (See Figure 15 

b

).

2.  Remove the jammed Banknote (See Figure 15 

c

).

3.  If the Banknote jam location is still not evident, 

unlock and pull the Stacker Box out of the Frame 

Unit (See Figure 16 

a

).

4.  Remove any jammed Banknote found there 

(See Figure 16 

b

). 

Cleaning Procedure

To clean the EBA-40 Validation Section, gently rub 

the Sensors and Rollers clean using a dry, soft, 

 

lint-free, Micro-fiber Cloth ONLY. 

 

Do not use any Alcohol, solvents, Citrus based 

 

products or scouring agents that may cause damage 

to the Validation Section Sensors and/or Rollers.

S

ENSOR

 

AND

 R

OLLER

 C

LEANING

 P

ROCEDURE

To clean the EBA-40 Unit’s Sensors and Rollers, 

proceed as follows:

1.  Turn the EBA-40

 

Unit and the Host Machine’s 

Power Supply’s 

OFF

.

2.  Open the EBA-40 Units Front and Rear Guide.
3. Clean 

the 

appropriate 

path and Lens of each 

 

Sensor.  

5 PREVENTIVE MAINTENANCE

a

b

Figure 14 

Retrieving Banknotes

a

b

c

Figure 15 

Clearing an Entrance Banknote Jam

a

b

Figure 16 

Clearing a Stacker Box Banknote Jam

NOTE: If a Banknote jam occurs when the 
Centering Mechanism is closed, the cover 
will not open. To un-jam the Unit, rotate the 
Centering Guide Shaft out of the way by 
using a Hex Nut Driver, and then open the 
Top Cover and remove the jam.

Caution: Do not use Alcohol, thinner or 
Citrus based products for cleaning any 
Banknote transport Sensors or 
surfaces. The lenses can become 
clouded by chemical evaporation 
residue that may cause acceptance 
errors.

Содержание EBA-40















































Отзывы: