manualshive.com logo in svg
background image

13

21-18ID
Instruction & User Manual

OPERATING INSTRUCTIONS

Intended Use

This impact driver is intended for percussive 
tightening and loosening of nuts, screws and 
other fixings.
The tool must not be modified or used for 
any other purposes than the ones described in 
these instructions.

Battery

Make sure the ON/OFF Trigger (4) is not 
operated when inserting or removing the 
battery. Use only JCB batteries: 21-15LI, 
21-20LI, 21-30LI, 21-40LI and  21- 50LI.

NOTE

 

m

Do not use excessive force when 
inserting the JCB battery in the 
power tool. 

An incorrectly connected 

battery can damage the battery terminals or 
the battery socket on the power tool.

 

m

Use the button (10) on the battery to check 
the charging status; 4 red LEDs indicates 
fully charged, where 1 indicates low battery 
charge status.

Charging The Battery

After charging for the first time, ensure the 
battery is completely discharged before 
placing on charge again. Repeat this charging 
and discharging cycle 4 to 5 times to ensure 
battery is correctly conditioned.

WARNING!

 

m

Place the battery charger on a level and 
stable surface. Plug the charger into a 
suitable power point.

 

m

Connect the battery to the charger so that it 
clicks into place. 

 

m

Refer to the Battery Charge Level table 
below for battery charger status as indicated 
by LED lights.

 

m

Unplug the charger from the power point 
prior to removing the battery from the 
charger.

Battery Charge Level

Red 

LED

Green 

LED

Battery Charge Status

Charger is connected to 
mains power
Connected battery is 
charging
Connected battery is fully 
charged
Connected battery has a 
charging fault
Charger is outside correct 
operating temperature 

If the LEDs on the charger do not come on 
when charging:

 

m

Check that the charger’s mains plug is 
properly inserted into the power point.

 

m

Check that the battery is correctly inserted 
in the charger.

Connecting the battery

 

m

Connect the battery to the battery socket 
on the power tool so that it clicks into place.

Removing the battery

 

m

Press the battery release button (6) and 
remove the battery from the power tool.

21-18ID Impact Driver Manual 2021.indd   13

17/06/2021   12:03

Содержание 21-18ID






















Отзывы: