manualshive.com logo in svg
background image

15

21-18BLCD
Instruction & User Manual

Torque Setting

Only use the torque setting ring when the 
tool is stopped and the chuck is not rotating. 
Otherwise the tool can be damaged.

WARNING!

 

m

Before you start working you should test 
your selection to find a suitable torque 
setting on a sample of the same material as 
the work piece.

 

m

The lowest torque is with the arrow 
pointing to 1. Higher numbers mean higher 
torque.

 

m

To use the highest torque the tool can 
produce, set the mode selector to the drill 
symbol. In this mode the torque inhibitor is 
not activated.

 

m

For driving screws, especially in wood, a low 
torque should be selected to reduce the 
risk of damaging the screw head, thread or 
work piece.

 

m

A high torque setting is best for drilling. 

Mode Selector

Drilling Mode

Use the correct specification of drill bit for 
the material and power tool you are working 
with. Incorrect selection may cause damage 
to the tool, workpiece or bit.

WARNING!

Check that the drill is correctly inserted 
and the chuck is properly tightened before 
starting the tool.

NOTE

 

m

If loose, clamp the work piece. The work 
piece should lie flat on a workbench, and/or 
be securely fixed.

 

m

Mark out the position of the hole by suitable 
means. 

 

m

Use a suitable drill for your material.

 

m

Ensure all drills are sharp.

 

m

When drilling in metal, make sure that the 
drill is always sufficiently cooled with a non-
flammable liquid.

 

m

Start drilling at low speed.

 

m

If you are drilling large holes, pre drill with a 
small drill and then finish off with a large drill.

 

m

Do not force the tool - do not press too 
hard on the drill.

The drill can jam in deep holes. Release the 
power switch immediately if the drill jams. 
Switch to anticlockwise rotation and run the 
drill loose at low speed.

NOTE

Hammer Drilling Mode

 

m

Set the selector ring in hammer mode to 
connect the hammer function. The hammer 
function allows more effective drilling into 
hard, brittle materials such as concrete, brick 
and stone.

Screw Driving Mode

Check that the bit is correctly inserted and 
the chuck is properly tightened before start-
ing the tool.

NOTE

 

m

Do not over-tighten screws. 

This risks 

damaging the screw head or thread.

Содержание 21-18BLCD





















Отзывы: