background image

14

JCB-18BLDD

Instruction & User Manual

Replacing Bits/Drills

Never hold the chuck sleeve in one hand 
and run the tool to tighten or release
accessories. This risks serious personal injury.

WARNING!

 

m

Place the tool on a stable surface, for 
example a work bench.

 

m

Open the chuck by holding the chuck sleeve 
in a firm grip and turning it anticlockwise 
until the chuck jaws open and the accessory 
can be inserted. The chuck is designed so 
that it can easily be tightened or released 
with one hand.

The spindle locks automatically when the 
chuck stops rotating.

NOTE

 

m

Insert the accessory as far as it will go into 
the chuck. Point the tool up slightly so that 
the accessory does not fall out.

 

m

Tighten the chuck sleeve clockwise so that 
the accessory is gripped firmly by the chuck 
jaws.

Check that the accessory is straight, centred 
and not askew. If the accessory is not
properly positioned it could fly out when 
starting the tool. Check that the chuck jaws 
rest on the flat surfaces of the accessory.

NOTE

 

m

Tighten the chuck until it grips the accessory. 
Grip the chuck firmly and turn it clockwise.

Power Switch

 

m

Press the power switch to start the tool. 

The tool has variable speed:

 

m

Press the power switch to increase the 
speed.

 

m

Release it slightly reduce the speed.

 

m

Release the power switch to stop the tool.

Direction Selector

Only use the direction selector when the 
tool is stopped and the chuck is not rotating.
Otherwise the tool can be damaged.

WARNING!

 

m

Use the direction selector to switch 
between clockwise rotation and 
anticlockwise rotation.

 

m

When the direction selector is in the middle 
position the power switch is locked and 
cannot be pressed.

 

m

Always put the direction selector in 
the middle position before putting 
the tool down

. This reduces the risk of 

accidentally starting it.

 

m

Press in the direction selector with the 
arrow pointing to the chuck for rotation to 
the right/screwing/drilling.

 

m

Press in the direction selector with the 
arrow pointing away from the chuck for 
rotation to the left/unscrewing.

High torque tool, use with care.

WARNING!

Содержание 18BLDD






















Отзывы: