background image

6

Auto On/Standby

The JBL On Air WEM-1 will automatically enter the Standby mode after
approximately 10 minutes, when no signal is detected from your system. The
WEM-1 will then power on instantly when a signal is detected. When Mute 

0

is engaged, auto turn-off is deactivated. 

LED Color

Transmitter Module

Receiver Module

Green

Transmitter and receiver module Transmitter and receiver module
are communicating (RF lock)

are communicating (RF lock)

Blinking Green

Transmitter and receiver are

Transmitter and receiver are 

(Slow)

not communicating (no RF lock) not communicating 

(no RF lock)

Blinking Green

Not applicable

Receiving IR command

(Fast)

from remote control*

Red

Standby

Standby

(no signal being received)

(no signal being received)

Orange

Not applicable

Local input is selected

Blinking Orange

Not applicable

System muted (when local

(Slow)

input is selected)

Blinking Orange

Not applicable

Receiving IR command

(Fast)

from remote control* (when 
local input is selected)

* Blinking stops when unit reaches minimum or maximum volume setting

Subwoofer Output

The JBL On Air WEM-1 includes a subwoofer output 

9

on the receiver module.

This output allows you to feed the low-frequency sounds to a separate powered
subwoofer. A powered subwoofer will deliver deeper bass response than is 
possible with speakers alone.

To connect a powered subwoofer to the receiver module, simply connect the 
Sub Out 

9

on the receiver module to the line-in on the rear of the powered 

subwoofer, using a 1/8-inch stereo mini-jack/RCA cable (not included). Please
note that this output is full-range and not filtered or low-passed. Make sure that
your powered subwoofer features a low-pass crossover network and that this
crossover is indeed selected. Do not use the LFE input on a powered subwoofer,
as it is not filtered and you will be hearing a lot of undesirable higher-frequency
information from your subwoofer.

A Word About Wireless Products

The JBL On Air WEM-1 utilizes advanced wireless transceivers operating in the
2.4GHz frequency band. This is the same frequency band that is used for wireless
home networks and high-quality cordless phones. It also allows the transmission of
high-performance, full-spectrum sound to remote locations, wirelessly.

Like all wireless devices, the WEM-1 wireless speaker’s operating range may
vary, depending upon variables such as building construction methods and 
materials, atmospheric conditions and other sources of interference. Please
consult your JBL dealer or distributor, or visit www.jbl.com, for further 
information or assistance.

Wall-Mounting

Adjustable wall brackets are included for the transmitter and receiver modules.
The included brackets are for wall-mounting only; they are not to be used for
ceiling-mounting. Ceiling-mounting of the WEM-1 transmitter and/or speakers
is not recommended, regardless of bracket used.

Wall-Mounting the Transmitter Module

Caution

The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the module. 

Step 1

.

Insert the two M3 x 4 machine screws through the wall bracket and into the
rear of the transmitter module, as shown in Figure 5.

Figure 5.

Step 2.

Attach the transmitter module with wall bracket to the wall, using two suitable
screws (and wall anchors, if necessary).

Wall-Mounting the Receiver Module

CAUTION:

The customer is responsible for proper selection and use of mounting hardware
(available through hardware stores), to properly and safely wall-mount the module. 

Step 1

.

Turn receiver module over and remove all four corner screws, 
as shown in Figure 6.

Figure 6.

Step 2.

Attach the wall bracket to the left and right side, as shown in Figure 7.

Step 3.

Reattach the four screws removed in Step 1 through the brackets into the
receiver module, as shown in Figure 7.

Figure 7.

Step 4.

Attach the receiver module with wall bracket to the wall, using four suitable
screws (and wall anchors, if necessary).

JBLP2744-WEM1-OM.qxd  10/29/08  2:42 PM  Page 6

Содержание WEM-1









Отзывы: