29
JBL VLA-C SERIES
| USER’S GUIDE
VLA-C125S
Dual 15” Subwoofer Array Module
System:
Frequency Range (-10 dB)
1
:
52 Hz – 210 Hz
Frequency Response (±3 dB)
1
:
62 Hz – 123 Hz
System Power Rating
2
:
1600 W Continuous Pink Noise (6400 W peak), 2 hrs
800 W Continuous Pink Noise (3200W peak), 100 hrs
Maximum Input Voltage:
80 V Rms (2 hrs), 160 V peak
Maximum SPL (1m)
3
:
127 dB Cont. Ave (2 hrs), 133 dB Peak
Sensitivity
4
:
98 dB (52 Hz – 210 Hz, 2.83V)
Impedance:
4Ω, 3.0Ω min @ 195 Hz
Amplifiers:
Crown DCi Family with DSP on-board
Recommended:
Crown DCi 2 | 2400N
Crown DCi 4 | 2400N
Transducers:
Low Frequency Driver:
2 x 2275H, 304 mm (15 in) diameter , each with two 76 mm (3 in) diameter voice coils, Neodymium Differential
Drive
®
, Direct Cooled
™
Physical:
Enclosure Material:
Fiberglass shell, gelcoat finish, with 18 mm Birch plywood internal bracing.
Grille:
Powder coated 14 gauge hex-perforated steel with zinc under-coating, backed with acoustically transparent cloth
and hydrophobic screen.
Inter-Enclosure Angles:
VLA-C125S to VLA-C125S: 0° using VLA-C125S Bracket Plate (included with VLA-C125S)
VLA-C265 below VLA-C125S Subwoofer (VLA-C265 cannot be connected above C125S): 0°, 5° using VLA-C125S
Bracket Plate (included with VLA-C125S)
VLA-C2100 below VLA-C125S Subwoofer (VLA-C2100 cannot be connected above C125S): 0°, 7.5° using VLA-C125S
Bracket Plate (included with VLA-C125S)
Environmental:
IP-55 rating per IEC529 (dust protected and protected against jets of water).
Terminals:
CE-compliant covered barrier strip terminals. Barrier terminals accept up to 5.2 sq mm (10 AWG) wire or max width
9mm (0.375 in) spade lugs. Touch-proof covers. Full set of terminals on back panel, plus optional-use inter-cabinet
connection terminals located on top and bottom panels of cabinet.
Colors:
-GR: Gray (similar to Pantone 428C), -BK: Black
Dimensions (H x W x D):
508 x 848 x 634 mm (20.0 x 33.4 x 24.9 in)
Net Weight (ea):
56.7 kg (125 lbs)
Shipping Weight (ea):
62.6 kg (138 lbs)
Included Accessories:
2 x VLA-C125S Bracket Plates
8 pcs. M10 x 35 mm stainless steel bolts (1.5mm pitch, 6 mm hex-drive) for attaching Bracket Plates
2 pcs. Plastic Trim Cover Panels for Bracket Plates, each attaches via
4 pcs (8 total) 3-32 x ½” trusshead, phillips-drive, stainless steel bolts.
Optional Accessories:
VLA-C-SB Suspension Bar Kit -- For top & bottom of the array, includes 2 identical Suspension Bars (for top/bottom),
4 pcs ¾-inch Class 2 Screw Pin Shackles (must use 2 Shackles for each Suspension Bar, located at end channels, not
in the center).
VLA-C125S-ACC kit – For adding terminal cup to front to allow easy and neat cardioid subwoofer wiring.
VLA-C-ACC kit – For adding front baffle terminals for cardioid subwoofer configuration.
1. Using recommended DSP tuning, full-space (4π)
2. Continuous Pink Noise rating is IEC-shaped pink noise with 6 dB crest factor. Peak defined as 6 dB above Continuous Pink Noise Rating.
3. Continuous Average calculated from sensitivity and power handling, exclusive of power compression. Peak measured, unweighted SPL, bi-amp mode,
measured under full-space conditions at 1 meter using broadband pink noise with a 12 dB crest factor and specified preset.
4. 2.83 V RMS, full-space (4π)
JBL continually engages in research related to product improvement. Some materials, production methods and design refinements are introduced into
existing products without notice as a routine expression of that philosophy. For this reason, any current JBL product may differ in some respect from its
published description, but will always equal or exceed the original design specifications unless otherwise stated.
