background image

 

- 18 - 

SDEC -X000 DACS Calibration Manual v1.0.doc 

 

9  Setting Output Level 

9.1  Setting Levels before Calibrating 

Using the internal noise generator of the SDP set all outputs to 
achieve 75dB using the “C” weighting and “SLOW” response. 
This will maintain the best signal to noise and headroom 
possible by optimizing the gain structure of the system. 

9.2  Final Level Set after Calibrating 

Setting the final output level should be done 

after

 all corrective 

EQ has been completed. It is very important that this be done 
so that all channels have a good balance and are properly 
calibrated for the average output in the mid-band frequencies. 
Use the internal noise test from the SDP and test one channel 
at a time. 
 

 

Set main and surround channels to 75db. 

 

Set the subwoofer channel to average between 82dB-
85dB. 

9.2.1 

Level Matching Multiple Surround 
and Subwoofer Channels

 

The SDEC-4000 has multiple outputs for Subwoofers and Side 
Surrounds. These will need to be level matched to each other 
before final output levels are set. 
1.  Using the internal noise test of the SDP test each output 

individually. It will be necessary to mute the output you are 
not testing. Make sure the 

Trim Link 

is off (not RED). 

2.  Once you have set each to the reference level of 75dB 

enable the 

Trim Link

 feature so that the led turns 

RED

.  

3.  With all the multiple channels un-muted test together and 

adjust the output to reach the same reference level. You 
will now have an output that has all the multiple channels 
level matched and the overall output set to the reference 
level. Follow the instructions for level matching the 
multiple surrounds and subwoofer channels first and then 
set the overall output level to the following reference level. 

9.3  Using the SPL Meter 

9.3.1 

Analog SLM Instructions

 

NOTE:

 All instruments of this type are most accurate when 

operated in the upper end of the selected range. You should 
always use the lowest 

RANGE 

setting possible. For example, if 

you are balancing a system using the Surround Processor's 
noise generator (75dB) you would set the 

RANGE 

selector to 

70dB

 
1.  Rotate the RANGE Selector clockwise one click to the 

BATTERY TEST position. Observe the meter indication. A 
reading anywhere within the red BATT TEST range 
indicates adequate battery power. If the indication is below 
this range, replace the battery before using the instrument. 

2.  Now rotate the RANGE Selector clockwise to the desired 

range. The meter has a display range from -10dB to +6dB. 
The 0dB point corresponds to the RANGE selected. 
Therefore, if the 80dB RANGE is selected, a 0dB reading 
will equal 80dB. 

3.  Slide the WEIGHTING Selector to "C" weighting for 

channel balance tests. "A" weighting cuts low frequencies. 
This will cause errors when measuring subwoofers. 

4.  It is recommended that you slide the RESPONSE Selector 

to the SLOW position. This slows the meters response to 
sudden changes in sound level which can make average 
level readings difficult. 

 

9.3.2 

Digital SLM Instructions

 

NOTE:

 All instruments of this type are most accurate when 

operated in the upper end of the selected range. You should 
always use the lowest 

RANGE 

setting possible. For example, if 

you are balancing a system using the Surround Processor's 
noise generator (75dB) you would set the 

RANGE 

selector to 

70dB

. In the event you have selected a range that is too low, 

an 

OVER-RANGE 

condition is indicated by a flashing display. 

Select the next higher range.  
 
1.  Turn the SLM on by rotating the 

RANGE Selector 

clockwise. Continue to rotate the 

RANGE Selector 

to the 

desired 

RANGE

2. 

Press the 

WEIGHTING 

button to select 

"C" 

weighting for 

channel balance tests.

 

3. 

It is recommended that you slide the 

RESPONSE 

Selector 

to the 

SLOW 

position. This slows the meters 

response to sudden changes in sound level which can 
make average level readings difficult.

 

4. 

Check the display for a low battery indication. If the battery 
needs replacing, 

BATT 

will appear in the upper left-hand 

corner of the LCD display. Replace the battery if 
necessary.

 

 

Содержание Synthesis SDEC-3000

























Отзывы: