JBL STADIUM UB4100, Руководство пользователя

Страница: 4 / 8

WHEN YOU HAVE COMPLETED ALL OF THE SOUNDBAR
CONNECTIONS:
1. Insert the 40A fuse into the fuse holder you installed on the soundbar power wire.
2. Re-connect the vehicle’s negative (–) battery terminal.
3. Pair the supplied Bluetooth remote control with the soundbar:
a. Set the soundbar’s rear-panel power switch to On.
b. Insert the supplied battery into the remote’s battery compartment with its “+”
side UP.
c. Press the remote’s “+” button.
LISTENING TO YOUR SOUNDBAR
Turning the Soundbar On and Off
Set the soundbar’s rear-panel power switch to On. This will put the soundbar in the
standby mode. To turn the soundbar on, press the Standby button on the soundbar’s
end panel:
If your source unit does not have RCA outputs use the supplied bare wire-to-RCA
adapters to connect the source unit’s speaker wires to the soundbar’s audio input
cable, as shown in the illustration below.
2. Position the soundbar in the desired location against the vehicle mounting bar. Use
4 of the supplied mounting bracket bolts to secure each bracket top to a bracket
base. Two sets of bolts are supplied, allowing the soundbar to be mounted to
pipes from 1” (25mm) to 3-1/2” (89mm) in diameter.
a. When the soundbar is in the correct position, tighten the mounting bracket
adjustment screws as tight as possible using your fingers, then insert the
supplied small hex wrench into the holes on the adjustment screws and use
it as a lever to secure the screws as firmly as possible.
3a. Run one end of one safety harness wire through one of the soundbar’s harness
attachment loops, and use the supplied clamp to secure the wire.
IMPORTANT: Be sure to tighten the bolts on the clamp as far as they will go and
test the connection to be sure that the safety harness wire is secure in the clamp.
3b. Run the other end of the safety harness wire around the vehicle mounting bar and
use the supplied clamp to secure the wire.
IMPORTANT: Be sure to tighten the bolts on the clamp as far as they will go and
test the connection to be sure that the safety harness wire is secure in the clamp.
3c. Repeat Steps 3a and 3b with the other safety harness wire, using the other
soundbar harness attachment loop and the vehicle mounting bar.
IMPORTANT: Be sure to tighten the bolts on the clamp as far as they will go and test
the connection to be sure that the safety harness wires are secure in the clamps.
Vehicle Chassis
(bare metal)
Battery
Illumination
Remote
Turn-On
Orange/White
Wire
Blue/White
Wire
To illumination or
accessory circuit
To head unit
remote wire
Soundbar
Wiring
Harness
Black
Wire
Red
Wire
40A
Fuse
+12V Ground
18”
(46 cm)
AUDIO INPUT CONNECTIONS
Connecting to an audio system head unit
Connect the source unit’s RCA line
outputs to the soundbar’s (black)
RCA audio input cable, as shown in
the illustration below.
Audio System
Head Unit
Front L/R
Audio Out
Black RCA
Audio Cable
Audio
Input
Soundbar
Wiring
Harness
When you’re finished connecting the source unit’s speaker outputs to the adapters,
plug the adapters into the amplifier’s input connectors as shown in the previous
illustrations.
Connecting to a mobile phone or portable audio device
Connect the mobile phone’s or portable device’s headphone port to the soundbar’s
black 3.5mm audio cable, as shown in the illustration below.
From mobile phone or
portable audio device
Audio
Input
Soundbar
Wiring
Harness
Black 3.5mm
Audio Cable
Connecting to a subwoofer or secondary amplifier
Connect the subwoofer or a secondary amplifier to the soundbar’s (gray) audio output
cable, as shown in the illustration below.
To subwoofer or
secondary amplifier
Gray RCA
Audio Cable
Audio
Output
Soundbar
Wiring
Harness
GROUND, POWER, ILLUMINATION AND REMOTE
CONNECTIONS
IMPORTANT: Disconnect the vehicle’s negative (–) battery terminal before
beginning the installation.
Connect the soundbar’s +12V power (red), ground (black), illumination (orange/white)
and remote turn-on (blue/white) wires as shown below.
• Use sandpaper to clear the paint from the metal surface at the ground connection.
Use a star-type lock washer to secure the connection.
• Install a fuse holder for a 40A fuse on the power (12V) wire within 18” (46cm) of the
(+) battery terminal. Do not install the fuse in the holder at this time.
a.
a.
b.
ON
OFF
AUTO
EXT LO
HI
Standby
Button
Bluetooth
Button
Page 2