17
Features
1. POLARITY
LED
– This light indicates whether the
polarity is set to Normal or Inverse Polarity. When
the light is ON, speaker polarity is inverted.
2. POLARITY
Button
– This push button allows you
WRFKRRVHEHWZHHQ1RUPDORU,QYHUVH
3RODULW\7KHFRUUHFWSRODULW\VHWWLQJZLOOSURGXFH
the best blend between the subwoofer and the
full-range speaker and the strongest perceived
bass response at the listening position. If the bass
response seems weak, try inverting the polarity.
NOTE:
This button is also used to Factory Reset
speaker settings. See
“FACTORY RESETS” on
page 19
for more information.
3. FRONT LED Button
– This push button allows
you to turn on/off the Power LED on the front of
the speaker. The front LED will illuminate BLUE
when the system has power and is ready to pass
audio.
4. LIMIT
Indicator
– There is one YELLOW LED
indicator that will illuminate when input clipping
occurs or peak output has been reached and the
DSP limiter is acting.
5. GAIN
Knob
– This gain knob is for setting the
input level. The 12 o’clock position is a good
starting point for most uses. Once the full-range
system has been connected the level can be
varied to match and deliver the desired balance.
6. SIGNAL
Indicator
– There is one GREEN LED
that will illuminate when signal is present.
7. XLR
Inputs
– Female balanced XLR and 1/4 inch
phone jack combo input connectors.
8. WI-FI LINK LED
– This LED has four states:
a. Off
– The speaker is not connected to WI-FI.
b. On
– The speaker is connected to WI-FI.
c. Blinking
Slowly
– The speaker is in Access
Point mode and has not yet established a WI-
FI connection.
d. Blinking
Rapidly
– The speaker is in Access
Point mode and is communicating with a
connected device.
9. WI-FI CONNECT Button
– This button is used
to connect to a WI-FI network for speaker
FRQ¿JXUDWLRQDQGFRQWUROXVLQJWKH35;&RQQHFW
application. This button has two functions:
a. Press and release
– Instructs the speaker to
WU\FRQQHFWLQJWRWKHFRQ¿JXUHG:,),QHWZRUN
b. Press and hold for 2 seconds
– Switches
between “Access Point” and “Normal” network
operating modes. By default, the speaker is in
“Normal” network operating mode. Switching
to Access Point mode allows all PRX800W
VSHDNHUVLQDV\VWHPWREHLQLWLDOO\FRQ¿JXUHG
for your network router. When switched to
Access Point mode, the WI-FI LINK LED will
ÀDVKVORZO\
For more information on using WI-FI, see
“WI-FI
SETUP” on page 18
.
10. HI-PASS LED
– This LED will light to indicate the
+,3$66¿OWHULVHQDEOH58FRQQHFWRU
11. HI-PASS Button
– This push button determines
whether the signal coming out of the THRU
FRQQHFWRULVXQDOWHUHG)8//5$1*(RUKDV
DKLJKSDVV¿OWHU+,3$66DSSOLHGWRLW%\
default, the speaker is in a FULL RANGE mode.
If HI PASS is selected, an 80Hz 24dB/Octave
KLJKSDVV¿OWHULVDSSOLHGWRWKHVLJQDOFRPLQJ
out of the THRU connector. Engaging the high-
SDVV¿OWHUDOORZVIRUDVPRRWKWUDQVLWLRQEHWZHHQ
the subwoofer and full-range speaker that is
connected to the output connector. This button
must be pressed and held for 2 seconds to switch
between options.
12. THRU Connectors
– Male balanced XLR output
connector. This connector provides a FULL
RANGE or HI PASS signal depending on the
setting of the HI-PASS button. In addition to
connecting a full-range system to the output, it’s
also possible to daisy chain subwoofers together.
13. REMOTE EQ LED
– Indicates the speaker has
settings applied by the WI-FI application.
14. POWER LED
– This LED illuminates when the
“Power Switch” has been turned to the on position.
It will illuminate BLUE when the system has power
and is ready to pass audio.
