background image

11

System Type:

Self powered 15", two-way, bass-reflex,  

Frequency Range (-10 dB):

45Hz -20kHz (EQ in flat position)

Frequency Response (±3 dB):

52Hz - 20kHz (EQ in flat  position)

Coverage Pattern:

70º x 70º nominal 

Directivity Index (DI):

10.3 dB

Directivity Factor (Q):

10.8 

Crossover Modes:

DSP controlled 48dB filter slope

Crossover Frequency:

1.6KHz 

System Power Rating: 

500 W continuous, 1000W peak

LF Power amp:

Class-D, 400 Watt (continuous) at driver impedance

HF Power amp:

Class-D, 100 Watt (continuous) at driver impedance

Distortion:

Less than 0.1% at rated power

Maximum Peak Output:

133dB SPL

1

Signal indicators:

Overload: Red LED indicates input overload condition 
Signal: Green LED indicates signal presents

Input sensitivity:

Mic position: -25 dBu to 0 dBu
Line position: +28 dBu to +10 dBu

Input Impedance:

64 K Ohms (balanced), 32 K Ohms (unbalanced)

EQ:

Presets for Main and Monitor position

LF Driver:

1 x JBL 265F 380 mm (15 in) Differential Drive

®

woofer

HF Driver:

1 x JBL 2408H 37.5 mm (1.5 in) annular polymer diaphragm, 
neodymium compression driver

Enclosure:

Trapezoidal, 18 mm, plywood with polypropylene end caps

Suspension / Mounting:

Dual 36mm pole socket

Transport:

2 x die-cast handles with backing cup

Finish:

Anthracite DuraFlex™ finish

Grille:

Powder coated, Anthracite, 18 gauge perforated steel 
with acoustical transparent black foam backing.

Input Connectors: 

Balanced XLR / 1/4 inch combo jack with XLR loop through, 

Dimensions (H x W x D):

815 mm x 440 mm x 465 mm
(32 in x 17.25 in  x 18.25 in) 

Net Weight:

26 kg  (57 lb.)

PRX515

1

Maximum Peak output measured with IEC pink noise at 1 meter in front of speaker baffle under free space conditions. Measurement instrument  

set to peak hold. Speaker muted and released at full power, recording maximum peak level.

Содержание PRX512M

































Отзывы: