background image

jbL anD harman internationaL

JBL is part of the HARMAN International, a group of companies with a common purpose: combining technology with a love of music to 
manufacture audio products that provide new levels of satisfaction, performance and value.

To promote variety and creativity, JBL operates independently in research and development. When it comes to translating the results 
of these efforts into actual consumer and professional products, JBL draws on the full combined strength of HARMAN International’s 
resources, which include one of the world’s most advanced manufacturing facilities. The result of this teamwork is that JBL’s renowned 
excellence in engineering is successfully carried through to each individual product, regardless of its application or price range.

As new audio concepts and technologies are pioneered, the partnership of JBL and HARMAN International guarantees that consumer 
and professional audio users everywhere will be able to enjoy their full range of benefits. 

JBL continually engages in research related to product development and improvement. Because of this, new materials, production 
methods and design refinements may be introduced into existing products without notice. For this reason, any current JBL product  
may differ in some respect from its published description, but will always equal or exceed the original design specifications unless 
otherwise stated.

 

HARMAN International Industries, Incorporated. 

8500 Balboa Boulevard, Northridge, CA 91329 USA

© 2012 HARMAN International Industries, Incorporated. All rights reserved. 

 JBL, K2, SonoGlass and Bi-Radial are trademarks of HARMAN International Industries, Incorporated, registered in the  

United States and/or other countries. Vented Gap Cooling is a trademark of HARMAN International Industries, Incorporated.

Dolby is a registered trademark of Dolby Laboratories.

DTS is a registered trademark of DTS, Inc.

Nomex is a registered trademark of E.I. du Pont de Nemours and Company.

SACD is a trademark of Sony Corporation.

Part No. JBLP4578 Rev: A 

www.jbl.com

Содержание Project Everest DD65000



























Отзывы: