JBL P-7520 Скачать руководство пользователя страница 3

3

• Always wear protective eyewear when

using tools. 

• When routing cables, keep input signal

cables away from power cables and
speaker wires. 

• When making connections, make sure

that each connection is clean, insulated
and properly secured. Observe the
polarity markings on the rear panel.
Refer to the application drawings to set
up the amplifier for operation in stereo,
bridged-mono, bi-amp or tri-mode con-
figurations.

• If the amplifier’s fuse must be replaced,

use only the same rating and type as a
replacement. Do not substitute another
kind.

Controls and Connectors

1. Pre-amp Level Input Connector –

Connects to line-level output from the
source unit. 

2. Universal Interface Speaker Level

Connector – Connects to speaker-level
output from the source unit. Provides
Common Sense amplifier turn-on
when used with factory radios 
(2-channel on P-7520, 4-channel on 
P-7540).

3. Pre-amp Level Output Connector –

Connects to other amps or processors
in the signal chain.

4. Speaker-Output Connector – (2-chan-

nel on P-7520, 4-channel on P-7540).

5. Fuses – P-7520: 30A ATC type, P-7540:

30A ATC type x 2, P-2510: 40A ATC
type.

6. Power Connector – Connection for

12V+, Gnd and Rem.

7. Input-Mode Switch – Sums left and

right inputs.

8. Input Sensitivity Control – Adjusts  

input sensitivity for pre-amp level and  
speaker-level inputs.

9. Pre-amp Output Selector Switch –  

Selects input path for pre-amp output.   
Output can be summed from front and  
rear inputs with no filter, or filtered by 
the front or rear crossover.

10.  Rear-Channel Input Selector – Selects  

rear-channel input between front input 
and rear input.

11. Crossover Selector – Determines   

whether the crossover is a High-Pass 
filter (HP), Low-Pass filter (LP) or  
unfiltered (flat).

12. Crossover Frequency Control – 

Determines the crossover frequency 
for the amplifier channels (front or   
rear) and the pre-amp outputs.

FUSE

30A

BRIDGE 

–      

R      

+

      L      

+

MADE IN THE U.S.A.

+

BATT

REM

GND

BRIDGE 

SPEAKER OUTPUTS

POWER

FRONT

REAR

30

FUSE

30A

30

+R–

+R–

–L+

–L+

AUX
OUT

R

L

R

L

FRONT

FRONT

REAR

LINE LEVEL

INPUT

SPKR LEVEL IN

REAR

ST MO

INPUT MODE

LEVEL

INPUT

PRE OUT

LEVEL

INPUT MODE
MO ST

6V

.250V

4V

.250V

FRONT 

F+R

FLAT

REAR

LP

FRT
LP

FRT

REAR

REAR 

XOVER

FLAT HP LP

XOVER

FLAT HP

LP

XOVER
AMP

XOVER

AMP

32Hz

80Hz

320Hz

32Hz

80Hz

2V

2V

320Hz

7540

R

L

LINE LEVEL

INPUT

SPEAKER LEVEL IN

R

+

L

+

AUX

OUT

R

L

30

–      

R      

+

      L      

+

+

BATT

REM

GND

FUSE

30A

MADE IN THE U.S.A.

BRIDGE 

SPEAKER OUTPUTS

POWER

PRE OUT

LEVEL

INPUT MODE

MO ST

4V

.250V

XOVER

FLAT

HP

LP

FLAT

HP

LP

2V

FREQ

32Hz

320Hz

80Hz

9

10

8

7

12

8

11

2

3

4

6

5

1

12

7

11

2

3

1

8

11

12

9

7

4

5

6

P-7520

P-7540

P-7520/7540/2510 OM copy  7/14/98 11:46 AM  Page 3

Содержание P-7520









Отзывы: