background image

Parameter

Specification

Unit

QA Test 

Limits

Conditions

Notes

Turn-on Transient

50 mV-peak

2v-pp

@ Speaker Outputs

AC Line cycled from OFF to ON

Turn-off Transient

50 mV-peak

2v-pp

@ Speaker Outputs

AC Line cycled from ON to OFF

Efficiency

Efficiency

65

%

64

Nominal Line voltage 120 VAC

Stand-by Input Power

24

Watts

26

@ nom. line voltage

Maximum allowable  input power under nominal  

Input voltage and frequency, HOT or COLD 

operation.

Power Cons. @ rated power

234

Watts

240

@ nom. line voltage

150 Watts @ 5.6 Ohms nominal line voltage

Protections

Short Circuit Protection 

YES

functional  Direct short at output

Amplifier should resume operation after short 

circuit condition removal 

Thermal Protection 

YES

functional

@1/8 max unclipped Power at 1.06 

times the input voltage

Temperature rise in accessible metal parts 

should not exceed 35K rise for domestic version 

or 30K rise for European versions (refer to 

requirements sheet).

DC Offset Protection

YES

-

DC present at Speaker Out leads

Design must insure no Offset at the speaker 

output  under any operating condition including 

abnormal operation

Line Fuse Rating

USA-Domestic 2

Amps

2

Type-T or Slo Blo-250 V

Internal fuse with UL/SEMKO rated holder

EU

1.25

Amps

1.25

Type-T or Slo Blo-250 V, Low 

Breaking capacity

Internal fuse with UL/SEMKO rated holder

4. ALL SPECS SHOULD BE MEASURED AT NOMINAL LINE VOLTAGE. 

SPEAKER CONNECTION

When we designed the 
E150P and E250P powered
subwoofers, our goal was 
to offer the user the best pos-
sible performance combined
with the most flexible and
complete installation options.
Please look over the following
three examples to determine
which description best
matches your system and 
follow the corresponding
hookup instructions.

To use the binding-post
speaker terminals with bare
wire, unscrew the collar until
the hole through the center
post is visible under the collar.
Insert the bare end of the wire

through the hole in the post,
then screw the collar back
down until the connection is
tight. The holes in the center
of the collars are intended for
banana-type connectors.

Speakers and electronics termi-
nals have corresponding positive
(+) and negative (–) terminals. It
is important to connect both
speakers identically: 
positive (+) on the speaker 
to positive (+) on the amplifier
and negative (–) on the speaker
to negative (–) on the amplifier.
Wiring “out of phase” results in
thin sound, weak bass and a
poor stereo image. 

NOTE:

The speaker-level con-

nection method described on

the next page is not a
preferred connection

 

 and should only be
resorted to if your receiver/
processor does not have a 
line-level or subwoofer output.
The customer is responsible for
proper connections, and any
damage to JBL or other equip-
ment due to improper connec-
tions will not be covered by
your JBL warranty. Consult with
your JBL dealer or an audio-
installation expert if you have
any questions about how to
connect your subwoofer using
the speaker-level inputs.

E250P 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Содержание E250P





























Отзывы: