ENGLISH
USER MANUAL
JB SYSTEMS
®
5/13
LIVESET 2
▪
Press [ENTER] to confirm your setting
If you want a program where the 4 projectors do exactly the same, you can enable the
SYNC mode
.
•
Press the
[MENU] button until the display shows [SyN].
•
Press the [ENTER] button to enter the mode.
•
Use the UP or DOWN buttons to select [Sy-M]
•
Press the [ENTER] button to enter button to confirm
Note:
The sensitivity of the build-in microphone can be set by turning the [microphone sensitivity] knob on
the rear of the Bar.
3)
FIXED COLOR STANDALONE MODE:
You can set a fixed color for the 4 RGB projectors together
•
Press the
[MENU] button until the display shows [CoL].
•
Press the [ENTER] button to confirm your choice.
•
[COLO] will appear on the screen
•
Press the [ENTER] button to enter the setup mode.
•
Use the [UP/DOWN] buttons to set the intensity of the red color. [r.000] = off, [r.255] = maximum
intensity
•
Press the [ENTER] button to confirm your choice and to go to the next color setting.
•
Use the [UP/DOWN] buttons to set the intensity of the green color. [G.000] = off, [G.255] = maximum
intensity
•
Press the [ENTER] button to confirm your choice and to go to the next color setting.
•
Use the [UP/DOWN] buttons to set the intensity of the blue color. [b.000] = off, [b.255] = maximum
intensity
•
Press the [ENTER] button to confirm your choice and to go to the strobe speed setting.
•
Use the [UP/DOWN] buttons to set speed of the strobe effect. [S. 00] = off, [S. 99] = maximum speed
•
Press the [ENTER] button to confirm your choice.
4)
MASTER/SLAVE STANDALONE MODE:
When you have several LIVESET units and you want them to all work synchronously, you can work in the
so called master/slave mode. To do this, just daisy-chain all the bars and make the settings of the desired
automatic or sound controlled program in the first bar of the chain (see description above). This bar is
called the Master unit.
Note: to send out the information from the master to the slaves, you also have to set the master unit in
MASTER MODE:
•
Press the
[MENU] button until the display shows [SyS].
•
Use the [UP/DOWN] buttons to select [M-En]
•
Press [ENTER]
•
Use the [UP/DOWN] buttons to select [on]
•
Press [ENTER] to confirm your setting
•
The first unit (master) is now set in Master mode. The LIVESET can now send information to SLAVE
units
Now put all the other bars is slave mode
. Once this is done, the “slave” bars will follow the orders of the
Master unit, so they work in perfect synchronicity.
To set a bar in slave mode:
•
Press the
[MENU] button until the display shows [SLA].
•
Press the [ENTER] button to enter this mode.
•
[S
…] followed by 3 numbers will appear on the display
•
Press the [ENTER] button to enter the address settings.
•
3 numbers will appear on the display. This is the slave address that you can set now by using the
[UP/DOWN] buttons:
o
If you select address [S001], the slave unit will execute the same patterns as the master unit
o
If you select a higher address like [S008], you can make the units working in sequences.
The program will start running in the master, then it will go on with the projectors in the slave
unit.
o
If you have more units (for example 3 units) and you put slave 1 for example on address
[S008] and slave 2 on address [S020]
→
The program will start running in the master, then it
will go on with the projectors of the slave 1 unit, followed by the projectors of the slave 2 unit.