ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
3/72
LED VICTORY SCAN / SPINNER
Important:
Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed
at least 50cm
from surrounding walls.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don’t cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
HOW TO SET UP THE UNIT
CONTROL PANEL:
1. DISPLAY
shows the various menus and the selected functions.
2. LEDS
DMX
On
DMX input present
MASTER
On
Master mode
SLAVE
On
Slave mode
SOUND
Flashing
Sound activation
3. BUTTONS
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
4. SCANMIRROR (LED VICTORY SCAN) or BARREL (LED SPINNER)
5. HANGING BRACKET:
with 2 knobs on both sides to fasten the unit and a mounting hole to fix a
mounting hook. The bracket can also be opened to put the effect on any horizontal surface.
6. WIRED REMOTE CONTROL INPUT:
Used to connect a simple CA-8 hand controller while the unit is
used in standalone or master/slave mode.
ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
4/72
LED VICTORY SCAN / SPINNER
7. WIRELESS REMOTE CONTROL INPUT:
Used to connect RF-8
wireless controller while the unit is used in standalone or
master/slave mode.
8. MAINS INPUT:
with IEC socket and integrated fuse holder, connect
the supplied mains cable here.
9. DMX INPUT/OUTPUT:
used for DMX512 linking. Use good quality
3pin XLR M/F balanced cable to link the units together.
10. SAFETY EYE:
used to attach a safety cable when the unit is rigged
(see paragraph “overhead rigging”
11. COOLING FAN:
used to cool the components inside the enclosure.
Make sure to never cover this fan outlet!
MAIN MENU:
To select any of the functions, press the MENU button up to when the
required one is shown on the display or use the DOWN and UP
buttons to browse the menu.
Select the function with the ENTER button (the display blinks).
Use DOWN and UP buttons to change the mode.
Once the required mode is selected, press the ENTER button to
confirm.
To go back to the main menu without any change press the MENU
button shortly. The main menu is shown in the chart.
DMX Address
Used to set the starting address in a DMX setup.
Press the MENU button until “
Addr
” is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to change the DMX512 address.
Once the correct address shows on the display, press the ENTER
button to save it.
To go back to the main menu without any change press the MENU
button shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Channel mode
Used to set the desired channel setup mode.
Press the MENU button until “
ChMd
” is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to choose 1MSL, 4MSL, 1, 7 or 8ch
(iSolution compatible) mode.
Once the desired channel setup mode shows on the display, press
the ENTER button to save it.
To go back to the main menu without any change press the MENU
button shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Slave Mode
Used to make the slave unit work in opposite to the master or to
work in complete sync.
Press the MENU button until “
SLMd
” is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
“SL 1”
(normal) or
“SL 2”
(2
light show) mode.
Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU
button shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Содержание LED Victory Scan
Страница 1: ......
