ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
6/8
HF-TWIN RECEIVER
HF-TWIN RECEIVER SETUP
Note:
Even if the transmitters and receiver have 16 channels, you cannot use 16 wireless systems together:
depending on the situation you will be able to use maximum 2 sets together.
While setting up more than one system, you should choose diff
erent channels for each set. It’s important that
you never choose consecutive channels. Instead try to divide the channels evenly over the 16 possibilities:
First setup one system and leave it switched on.
Setup the second system and check if it interferes with the first one (unwanted buzz noises etc.). In case of
interferences, select another channel for your 2
nd
set and try again until everything works well and leave the
set switched on.
•
Switch on the HF-TWIN RECEIVER by pressing the POWER switch (3).
•
Select a channel (1-8) for receiver A or a channel (9-16) for receiver B.
-
To setup the channel for the left receiver (A), press the
“SET” knob A (6) for about 2 seconds. The
channel number indicator (F) will start blinking. While this indicator is blinking you can select the de-
sired channel by pressing shortly the
“SET” knob (6) until the right channel appears on the display.
-
Wait for about 3 seconds until the blinking stops.
-
The receiver (A) is on the desired channel (1-8) now.
-
Do the same for receiver B by using
“SET” knob B (9) (channels 9-16) if you want to use 2 micro-
phones simultaneously.
-
Channel Frequencies:
CH 1
825 MHz
CH 9
828,3 MHz
CH 2
825,7 MHz CH 10
828,7 MHz
CH 3
827,3 MHz CH 11
829,2 MHz
CH 4
831,2 MHz CH 12
829,6 MHz
CH 5
824,5 MHz CH 13
830 MHz
CH 6
826,1 MHz CH 14
830,4 MHz
CH 7
826,6 MHz CH 15
830,8 MHz
CH 8
827,7 MHz CH 16
831,7 MHz
•
Now send the channel information to the microphone (HF-MIC or HF-BPACK) you want to use on each
receiver (A or B) by using the corresponding IR-knob. IR-knob A (5) for the left receiver (channels 1-8) or
IR-knob B (8) for the right receiver (channels 9-16).
•
Hold the microphone you want to synchronize with its IR-sensor in front of the IR-indicator (2) of the HF-
TWIN RECEIVER and press the IR-knob for about 2 seconds. The IR-indicator symbol (H) will start blink-
ing. When the blinking stops, the channel information has been send to the microphone or belt pack.
•
The HF-TWIN RECEIVER is now ready to be used.
•
Adjust the AF output from the left receiver (A) by turning it
’s volume knob (4) clockwise. Do the same for
the right receiver (B) by using the volume knob (10).
•
Switch off the HF-TWIN RECEIVER by pressing the POWER switch (3).
HF-MIC
– SETUP
•
First switch on the HF-TWIN RECEIVER and select a channel (1-8) for receiver A or a channel (9-16) for
receiver B.
•
Open the battery compartment (5) of the HF-MIC and insert two AA batteries (alkaline or rechargeable
battery).
•
Switch on the HF-MIC by pressing the ON/OFF switch (4) for a second. The display (2) will light up.
•
Hold the IR-sensor (3) of the HF-MIC in front of the IR-indicator (2) of the HF-TWIN RECEIVER.
•
Press the IR-KNOB A (6) or the IR-KNOB B (8) on the HF-TWIN RECEIVER for about 2 seconds. The IR-
indicator symbol (H) will start blinking 3 times. When the blinking stops, the HF-MIC has received the
channel information from the HF-TWIN RECEIVER and will now work with this part (A or B) from the re-
ceiver.
•
Do the same for a second HF-MIC if you want to use 2 microphones.
•
Speak through the mic: the AF indicator (A) will move to the rhythm of your voice.