![background image](http://html1.mh-extra.com/html/jayco/jay-feather-towables-2020/jay-feather-towables-2020_owners-manual_3621307089.webp)
Section 6: Electrical System
87
GFCI Receptacle
There is a ground fault current interrupter (GFCI) engineered into the electrical system. It is
designed to reduce the possible injury caused by electric shock. The GFCI will not protect
against short circuits or circuit overloads.
Test all GFCI receptacles monthly:
Push in the GFCI “TEST” button. The GFCI “RESET” button should pop out
indicating the GFCI receptacle has been “tripped” and interrupted 120-volt power.
Push in the GFCI “RESET” button to restore 120-volt power.
Contact your independent dealer for assistance if the GFCI “RESET” button does not re-
store 120-volt power and pops back out.
A “tripped” GFCI breaker indicates that abnormally high 120-volt current flow (a ground
fault) was detected. All ground faults must be repaired before use of the recreation vehicle.
If the GFCI “RESET” button does not restore 120-volt power and pops back out. Contact
your dealer for assistance.
5-Way and 8-Way Power Remote (if so equipped)
The remote is an optional item that may or may not be avail-
able for your RV.
This system gives you remote control over several functions in
your RV. The 5-way remote will operate (4) systems (with mo-
tors) and (1) light circuit. The 8-way remote will operate (7) sys-
tems (with motors) and (1) light circuit. Examples of systems with
motors include stabilizers, slideouts, and awnings. Both remotes
operate in a similar fashion; the 8-way will have more “pages”
on the display since it will operate more devices. The handheld
remote is located in a holder inside the entrance door.
Remote Operation
To power on the remote, press the silver (HOME) button. The dis-
play will prompt you for a pin and show numbers on the screen. The default pin is 0,0,0,0.
You should create a personal pin number. After you enter your pin number, the remote will
display a menu of devices that can be controlled. To power off the remote, press and hold
the “HOME” button for 5 seconds until the display goes dark.
Programming a Pin
The PIN code for the handheld remote provides personalized security, as well as a safety
feature to prevent inadvertent activation of functions. These instructions apply only to the
LCI wireless remote.
Reset the handheld remote PIN code
1.
Press the silver “HOME” button to turn the remote ON.
2.
Press and release the “HOME” button five times. The button
with a picture of a key changes to the word “CONFIG”.
3.
Press the “CONFIG” button. (
Fig 1-A
).
4.
The remote will ask to reset the screen lock PIN code (
Fig 2
).
5.
Press “Yes” (
Fig 2-A
)
6.
The remote will display a message that the PIN has been reset
(
Fig 3
).
7.
Press “HOME” button and press “Set PIN” (
Fig 4-A
).
8.
Enter a 4-digit PIN code (
Fig 5
).
Содержание JAY FEATHER Towables 2020
