![background image](http://html1.mh-extra.com/html/jayco/2016-jay-feather/2016-jay-feather_owners-manual_3619034049.webp)
SECTION 4-TOWING & SET-UP JAYCO TOWABLE
NOTE:
Locks on entrance and baggage doors need biannual lubrication using a light
coat of silicone spray. Conditions such as rain, salt, dust and pollution may increase the
maintenance needs.
K
EYLESS
E
NTRY
(
IF SO EQUIPPED
)
If your RV is equipped with a keyless entry system, it is a battery operated system.
Programming and changing batteries on the lock system are described in the following
sections.
For detailed instructions, please refer to the manufacturer’s operators manual included in
your warranty packet.
Battery powered keyless entry system:
The battery powered entry system is a 4 button touch pad programmable deadbolt lock.
The 4 buttons are labeled “1|2”, “3|4”, “5|6”, “7|8”. The button labeled “1|2” is the same
button whether the number 1 or 2 is desired. Please note this handle uses touch technology.
The buttons are activated by touch and do not require pressing the buttons. Touch the
button and lift finger from button for proper code entry.
Operation
The entry system incorporates proximity sensing to determine when you want to activate
the lock. To operate the lock you first must “wake up” the lock, by touching the “wake up
area” to the right of the buttons. The buttons will illuminate once the Touch Pad is
wakened. This indicates that the touch pad is ready for the code to be entered. (Refer to the
diagram on next page)
Preset Factory Code
The entry system has a factory set code of 3,7,1,5 followed by the Enter button. The Enter
button is the bottom button with the picture of the key. The Enter button is required to be
touched after the code is entered. The factory code resets every time the batteries are
removed for at least 10 seconds.
Programming New Code
To set a new code, wake up the lock by touching the “wake up area”. Then touch and hold
both the “3|4” button and the Enter Button for 2 seconds. The system will provide three
short beeps, indicating it is ready to accept a new code. Enter the new 4 digit code
followed by the Enter button. The system will provide four short beeps to indicate new
code acceptance. This new code will now activate the lock.
To reset the code, remove the batteries for at least 10 seconds. Re-install the batteries; and
follow the steps to
Programming New Code
.
System Fault Logic:
Action
Response
Ready to Accept New Code
Three short beeps
New Code Entered
Four short beeps
Wrong Code Entered
One long beep
Dead Bolt Locks
Two short beeps
Dead Bolt Unlocks
Two short beeps
Dead Bolt fails to Lock
One long beep
Dead Bolt fails to Unlock
One long beep
Low Battery
One Long beep after the Lock/Unlock beeps
4-5
Содержание 2016 Jay Feather
