![background image](http://html1.mh-extra.com/html/jayco/2016-alante/2016-alante_user-manual_3488309089.webp)
JAYCO CLASS A MOTOR HOMES
SECTION 8 – PLUMBING SYSTEM
8-13
6. Enter the motor home and open the cold water supply faucets to bleed air
from the water lines. When the water lines are nearly full, you may experience
some "air pockets." Allow them to escape before closing the cold water supply
faucets.
7. The water heater will fill first, followed by the supply lines and faucets.
8. Turn the appropriate (12-volt or 120-volt) water heater control switch ON.
To disconnect
9. Shut OFF the water at the external water source.
10. Disconnect the non-toxic drinking water hose and reinstall the city water
connection inlet cap.
C
ITY
W
ATER
T
ANK
F
ILL
Use this setting to fill the water tank using the city water tank fill.
1. If needed, sanitize the water system prior to travel.
2. Move the “water heater bypass valve” to the NORMAL position.
3. Remove the city water connection inlet cap and attach a non-toxic drinking
water hose to the inlet.
4. Place the utility center valves in the “City Tank Fill” position.
5. Turn ON the water at the external water source.
6. Water will flow into the fresh water tank.
To disconnect
During the filling process, periodically check the fresh water tank level using the
monitor panel located in the Command Center. When the fresh water tank is full, it
is normal to see water running from the fresh water overflow tubes onto the
ground.
7. Shut OFF the water at the external water source.
8. Disconnect the non-toxic drinking water hose and reinstall the city water
connection inlet cap.
C
OUNTRY
W
ATER
F
ILL
Generally speaking, this setting is used to fill the water tank when dry camping.
1. If needed, sanitize the water system prior to travel.
2. Move the “water heater bypass valve” to the NORMAL position.
3. Remove the city water connection inlet cap and attach a short non-toxic
drinking water hose running from your container of potable water to the city
water connection inlet.
4. Place the utility center valves in the “Country Fill” position.
5. Turn ON the water pump.
6. Enter the motor home and open the cold water supply faucets to bleed air
from the water lines. When the water lines are nearly full, you may experience
some "air pockets." Allow them to escape before closing the cold water supply
faucets.
7. The water heater will fill first, followed by the supply lines and faucets.
8. When at your campsite, turn the appropriate (12-volt or 120-volt) water heater
control switch ON.
To disconnect
During the filling process, periodically check the fresh water tank level using the
monitor panel located in the Command Center. When the fresh water tank is full, it
is normal to see water running from the fresh water overflow tubes onto the
ground.
Содержание 2016 ALANTE
