![background image](http://html1.mh-extra.com/html/jayco/2014-jay-flight/2014-jay-flight_owners-manual_635975054.webp)
SECTION 4
TOWING & SET-UP
JAYCO TOWABLE
4-10
Electric powered keyless entry system:
To prevent unauthorized access to your RV unique
Authority
and
Access
codes
must be programmed into the keyless entry keypad. Failure to do so allows
access by those with knowledge of the default code settings.
Definitions
Authority code
: A unique 5 digit pass code that gives the system
administrator (or owner) the ability to program keypad access codes. The
default
Authority
code is 7-7-7-7-7.
Access code
: A unique 5 digit pass code that is input into the entry keypad to
unlock the main entry door. Up to 5 separate access codes can be
programmed into the keyless entry system. The default
Access
code is 1-3-5-
7-9.
To lock the main entry door press the 1/2 button on the keypad for two seconds.
To unlock the main entry door enter the 5-digit
Access
code.
Prior to programming keyless entry keypads:
1. Retrieve the keypad
authority
code from the keyless entry owner’s
manual. If the keyless entry
authority
code is still set to the factory
default of 5 presses of the 7/8 button it must be changed for security
purposes. Failure to create a unique authority code specific to your RV
will allow access to your RV by anyone knowing the factory default
authority
code.
2. If a unique keypad
authority
code has already been assigned, and is
known, skip to programming processes
“B”
below.
If a unique keypad
authority
code has not been assigned, or if it is not known,
proceed to process
“A”
.
Keypad programming
- Process “A”
1. Gain access to the back side of the keyless entry keypad.
2. Plug the RV into 120-volt shore power and verify that the power converter is
operational (interior lights will be operational).
3. Connect the yellow wire exiting the back side of the keyless entry keypad to
chassis ground (B-) until the keypad beeps approximately 5 seconds). Note:
The black wire exiting the rear of the keypad always goes to chassis ground.
4. Disconnect the yellow wire exiting the back side of the keyless entry keypad
from chassis ground after the beep in step #3 occurs.
5. Enter a unique 5 digit
authority
code into the keypad. The keypad will beep
twice to confirm each button press and 3 times after the 5
th
button press.
6. Re-enter the same unique 5 digit
authority
code into the keypad. The keypad
will beep 3 times to confirm successful programming. A long beep indicates
programming failure.
7. Record the new
authority
code in a safe place for future reference. Note: The
authority code and the access code should never be the same for security
purposes.
8. Proceed to
process “B”.
Keypad programming
-
Process “B”
(use only after a unique
authority
code
has been assigned and is known).
1. Press and hold down the keypad 5/6 button for 5 seconds. The keypad will
beep indicating that learning mode has been entered.
Содержание 2014 JAY FLIGHT
