Jasco ZW3103 Скачать руководство пользователя

Страница: 7 / 16

Please Note: Z-Wave home control networks are designed to work

properly alongside 802.11 wireless computer networks, Bluetooth

and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video

devices and older cordless phones using the 900MHz frequency range

may cause interference and limit Z-Wave functionality. Many 900MHz

products have a switch to select channel “A” or “B”. You may find that

one of these channels will cause less interference than the other.

Key Features:

— One Z-wave controlled AC outlet for standard incandescent

lighting or dimmable CFL/LED

— Remote ON/OFF and Brightness control via the

Z-Wave controller

— Manual ON/OFF and Brightness control with the front

panel pushbutton

— Load-Sensing turns the light ON if the switch on the

connected light is used instead of the remote or pushbutton
on the Z-Wave module (default setting is disabled)

— One Always-ON pass-through AC outlet
— Space efficient design
— Does not block the lower outlet when plugged in to the

upper outlet of a duplex wall receptacle. (This assumes that
the duplex receptacle is mounted with the ground pin down.)

— Plugs and cords for connected devices route to the side

allowing close placement of furniture

— Grounded 3-wire power connection for safety

Содержание ZW3103

















Результаты поиска

Содержание ZW3103

Отзывы:

Похожие инструкции для ZW3103

Бренды по названию

Популярные бренды

Jasco ZW3103, Руководство пользователя

Результаты поиска

Содержание ZW3103

Отзывы:

Похожие инструкции для ZW3103

Бренды по названию

Популярные бренды