background image

pg 2 of 8

MODEL 400

JARVIS

6205005::::

®

1. Ensure

that employees wear eye protection in accordance with OSHA’s eye and face protection re-

quirements (29 CFR 1910.133) at all times.

2. Follow

our installation and maintenance instructions for proper installation and care of the tool.

3.

Enclosed are four (4) copies of

“NOTICE TO OPERATORS, MAINTENANCE AND CLEAN-

UP PERSONNEL.”

Post one copy on the employees’ bulletin board; give one copy to operator(s);

give one copy to the maintenance foreman; and give one copy to the sub-contract cleanup / internal

cleanup foreman.

Additional copies will be provided upon request.

4.

The tool is designed and intended to be powerful. That fact should be obvious to your employees,

but you must emphasize it to them.

5. Always

disconnect the tool from its power supply when it is not in use.

6. Ensure

that all employees who use this tool are trained in the proper use of this tool and are aware

of the dangers that may arise if they do not follow the procedures outlined in this brochure.

7. Hand/Wrist/Arm

injury and other Cumulative Trauma Disorders may result from repetitive work,

motion or vibration. You must make your employees aware of hazards, symptoms of injury and ap-

propriate prevention. See OSHA’s “Ergonomics Program Management Guidelines for Meatpacking

Plants.”

8. Remove

and

repair

any tool that malfunctions.

All

personnel must be instructed to remove any

malfunctioning equipment.

9. Never

make modifications or alterations to the tool.

Replace any missing or illegible labels.

10. Avoid

injury. Do not permit the tool to be misused.

11. If

you

resell

or

distribute

a Jarvis product, you must provide the purchaser with the appropriate safe-

ty sheets and tool brochure.

Additional copies of safety sheets and tool brochures will be provided

upon request.

SAFETY MESSAGES TO EMPLOYER AND SAFETY DIRECTOR

AVOID INJURY

Keep hands clear.

safety messages to employer

and safety director

Cutlerymania.com is an authorized online parts distributor supplying 

Original Jarvis Products.                                                                               . 

E-mail: [email protected] 

FAX: 973-751-7701    Telf: 973-751-7775     www.cutlerymania.com

Содержание Wellsaw 400









Отзывы: