en 3
2
5
6
7
IMPORTANT NOTE
If your garage does not have a side entrance, an external emergency
release should be installed. This allows for manual operation of the
garage door from the outside during power failure.
First, check whether your door is balanced and in equilibrium. Open
your door about halfway and let it go. The door can now hardly change
its position
independently
, but must remain in this position held by the
spring force alone.
1.
The rail of the garage door MUST be connected securely and firm
-
ly to the supporting wall or ceiling above the garage door.
2. Additional brackets and mounting rails (not included in the supply)
might be required, if the your garage ceiling has a cladding, boards
or similar.
3. If your garage does not have a separate side entrance, an external
emergency release (refer to section “Optional Accessories”) must
be installed.
Intended use
Before you begin
Door Types
Preparation
This garage door opener has been designed in accordance with the require-
ments of the EU Machinery Directive 2006/42/EC; GB (UK,NI): Supply of
Machinery (Safety) Regulations 2008 SI 2008 No. 1597. The garage door
opener has an integrated radio receiver. Optional accessories are available
and described, they may have different use. The garage door operator is
intended exclusively for the opening and closing of garage doors (please refer
to section 6 “Door Types”). The device is not meant for commercial use but
solely for the use in private garage doors that are appropriate for a single hou-
sehold. Note the manufacturers specifications regarding the door and operator
combination. The door must meet mechanical requirements according EU:
EN 12064; GB (UK, NI) BS EN12604. Any improper use of the drive could
increase the risk of accidents. The manufacturer assumes no liability for such
usage. Only the original accessories may be connected to the drive. With this
drive, the door must comply with the current and valid international and coun-
try-specific standards, guidelines, and regulations EU: EN 13241/EN 12543,
EN12604; GB (UK, NI): BS EN 13241/BS EN 12453/ BS EN12604.
3
4
Please check the supplied parts for completeness before starting the
installation. Note: The numbering only applies to the corresponding
section.
This figure always offers you a complete overview of the readyassem
-
bled system during the step by step installation of the system.
Scope of supply
Product overview
Hardwarebag:
14. Truss head screw 6 x
80 mm
1x
19. Safety cotter pin
1x
15. Lock nut M6
1x
20. Screw ST 6 x 50 mm
4x
16. Hexagonal head screw
4x
21. Screw ST 6,3 x 18 mm
8x
17. Nut M6
4x
22. Plug
4x
18. Bolt
1x
Parts overview:
1.
Drive head JL600
1x
7
.
Door bracket*
1x
2.
Drive head JL800/1000
1x
8
.
Adapter for gear wheel*
1x
3.
Remote control
2x
9.
Curved door arm 45° *
1x
4.
Rail bracket*
2x
10. C-bracket *
2x
5.
Hardwarebag*
1x
11. Hanging bracket *
2x
6.
Header bracket*
1x
12. Rail 8323CR5-JL*
1x
* Delivery with rail
Mechanical requirements according EU: EN12604 / GB (UK, NI): BS
EN 12604..
A. One-Piece Door with Horizontal Track Only.
B. One-Piece Door with Horizontal and Vertical Track – Special
canopy door arm is required and the Protector System™ required.
See your dealer.
C. Sectional Door with Curved Track.
D. Canopy door – Special canopy door arm and the Protector System
™ required. See your dealer.
E. The Canopy Door Arm for use on door types B and D.
F. Side moving sectional door - In the opening direction, the gap
between the main edge in open direction of a side moving sectio-
nal door and the opposite edge must be more than 500 mm. See
section F installation drawing.
Note:
The system JL600 cannot be used for one-piece garage doors
with horizontal and vertical guide rails and two-wing doors.
a. Header bracket
h.
Power cable
b. Belt
i.
Drive head
c. Rail
j.
Release
d. Carriage
k.
Straight door arm
e. Connecting piece
l.
Curved door arm
f.
Rail bracket
m. Door bracket
g. Hanging bracket