background image

ALIGN AND SLIDE DROP SIDE FROM  THE BOTTOM ONTO THE DROP SIDE UPPER AND LOWER TRACKS  ON THE LEFT 

OF THE LOWER DROP SIDE TRACKS (PULL TOWARDS YOU). RAISE DROPSIDE UNTIL IT IS LOCKED INTO  PLACE.

CAUTION: DO NOT FORCE THE DROP SIDE AS YOU MAY BREAK THE LOCKS, GUIDES, OR TRACKS. 
                 ATTACH RUBBER STOPPERS BEFORE OPERATING DROP SIDE.

 Note

: When moving the crib, DO NOT hold it by the drop side, always use the side frames to move the crib.

        WHEN ASSEMBLING THE DROP SIDE, MAKE SURE THE TEETHING RAIL IS ON THE TOP.

  

  

  

PHOTO A

PHOTO B

     

STAND AT THE MIDDLE OF THE DROP SIDE AND HOLD THE TOP RAIL WITH ONE HAND.  RAISE THE DROP SIDE

SLIGHTLY TO ENABLE YOU TO RELEASE THE LATCH BY PUSHING ON THE DROP SIDE LOWER RAIL WITH YOUR KNEE.

THE DROP SIDEWILL NOW LOWER. RAISE THE DROP SIDE AND IT WILL AUTOMATICALLY LOCK AT THE UPPER 

POSITION.

ALWAYS MAKE SURE DROP SIDE IS PROPERLY SECURED.

CAPRI SINGLE CRIB

STEP 4

AND RIGHT  FRONT POSTS.  MAKE SURE THE RELEASE LATCH ON THE LOWER GUIDES IS TO THE OUTSIDE

4

The release latch on the lower
guides must be on the outside

of the lower drop side tracks -

pull towards you before sliding

onto the track.

This rubber bumper must be installed prior 

to operating drop side - it will prevent drop 

side from falling to the floor

NOTE: Photos A & B are to demonstrate how the drop side should be installed.The photos of the wood components of the 
crib may differ from the crib purchased and are for reference only.

OPERATING INSTRUCTIONS FOR DROP SIDE.

Email: [email protected]

AFTER DROP SIDE IS 
INSTALLED ON THE TRACKS 
AND LATCHED IN THE "UP" 
POSITION, THREAD MACHINE 
SCREW INTO A RUBBER 
STOPPER  AND INSERT INTO 
EMPTY HOLE ON LOWER TRACK 
ASSEMBLY.  USE PHILLIPS 
SCREW- DRIVER 
(NOT PROVIDED) 
TO TIGHTEN BOLT

.

Machine Screw (6)

Rubber Stopper

RUBBER BUMPER(5)

                           BOLT (6)

A2

C

A1

B

PUSH

FRONT POST

ALIGN UPPER

GUIDE WITH
UPPER TRACK

LOWER TRACK ASSEMBLY
FACTORY INSTALLED

ALIGN LOWER

GUIDE ASSEMBLY
WITH LOWER 
TRACK ASSEMBLY

UPPER GUIDE
(ATTACHED TO
CRIB DROPSIDE

 (PART C

)

BOTTOM EDGE OF
CRIB DROPSIDE(PART C)

LOWER GUIDE 

ASSEMBLY

ON DROPSIDE(PART C)

AL

LGN 

BO

TH TRA

CKS

 FRO

M

 

UNDE

RNE

ATH

 THE

PU

LL 

UP

 

UNTI

L LO

WE

GU

LDE

 LATC

HE

S

Содержание CAPRI 0108L00








Отзывы: