Janome OC 6260 страница 11 Скачать руководство пользователя

Страница: 11 / 52

Raising and Lowering the Presser Foot

The presser foot lifter raises and lowers the presser foot.

You can raise it about 0.6 cm (1/4˝) higher than the

normal up position for easy removal of the presser foot,

or to help you to place thick fabric under the foot.

Lowered position

Normal up position

Highest position

Balancing Thread Tension

•

Auto tension

This machine features the Auto setting in the tension

control, which covers wide range of sewing condition. Set

the tension control dial at “Auto” for general sewing,

unless specifically indicated in this manual.

Correct tension:

The ideal straight stitch has threads locked between two

layers of fabric.

For an ideal zigzag stitch, the bobbin thread does not

show on the right side of the fabric, and the needle thread

shows slightly on the wrong side of the fabric.

Tension control dial

Setting mark

Needle thread

Bobbin thread

Right side of the fabric

Wrong side of the fabric

•

Manual tension adjustment

Manual tension adjustment may be needed depending on

the sewing materials, layers of fabric and other sewing

conditions.

Needle thread tension is too tight:

The bobbin thread will appear on the right side of the

fabric.

Loosen the needle thread tension by moving the dial to a

lower number.

Needle thread tension is too loose:

The needle thread will appear on the wrong side of the

fabric.

Tighten the needle thread tension by moving the dial to a

higher number.

Auto

Содержание OC 6260





















































Результаты поиска

Содержание OC 6260

Отзывы:

Похожие инструкции для OC 6260

Бренды по названию

Популярные бренды

Janome OC 6260, Инструкция

Результаты поиска

Содержание OC 6260

Отзывы:

Похожие инструкции для OC 6260

Бренды по названию

Популярные бренды