manualshive.com logo in svg

Janome JEM GOLD 660, Руководство по обслуживанию

Поделиться
Скачать
Janome JEM GOLD 660 Скачать руководство пользователя страница 2

1

CONTENTS

SERVICE ACCESS

FACE COVER ......................................................................................................... 2

BED COVER ........................................................................................................... 3

FRONT COVER ...................................................................................................... 4

REAR COVER ........................................................................................................ 5

MECHANICAL ADJUSTMENT

THREAD TENSION ................................................................................................. 6

PRESSER BAR HEIGHT AND ALIGNMENT ........................................................... 7

DISTRIBUTION OF NEEDLE SWING ...................................................................... 8

NEEDLE DROP ...................................................................................................... 9

NEEDLE BAR HEIGHT ......................................................................................... 10

HOOKTIMING ......................................................................................................... 1]

NEEDLE CLEARANCE TO HOOK ....................................................................... 12

BACKLASH (LOWER SHAFT GEAR) ................................................................... 13

FEED DOG HEIGHT ............................................................................................. 14

STRETCH STITCH BALANCE .............................................................................. 15

BUTTONHOLE STITCH BALANCE ....................................................................... 16

ADJUSTING THE LINE TACK WIDTH AND

DISENGAGEMENT CLEARANCE OF CAM FOLLOWER ............................ 17

WIRING OF TERMINAL BLOCK ............................................................................ 18

Содержание JEM GOLD 660




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды