manualshive.com logo in svg

Janome DC4030P, Руководство по обслуживанию

Поделиться
Скачать
Janome DC4030P Скачать руководство пользователя страница 24

23

DC4030P

Printed circuit board "F"

Setscrew

Setscrew

Printed circuit board "A"

TO REMOVE:

1.  Remove the front cover (see page 4).
2.  Unplug the connectors from the board "A".
3.  Remove the 8 screws and remove board "A".

NOTE:  TO DISCONNECT THE CONNECTORS:

1.  Grasp the connector directly with your fingers and pull.
  Do not pull on the lead wire, as this may damage the contact sleeve inside theconnector.
2.  When disconnecting the machine socket and power transformer connectors, pull them while 

pushing them toward the a board to unlock them.

TO INSTALL:

4.  To install, follow the above procedure in reverse.

NOTE:

  When installing board "A"  in the machine.
  The transformer wire should not pass over the capacitor when board "A" is installed.
  If the cord is resting on the capacitor, it may interfere the pattern selector button after the front cover is 

installed. 

REPLACING PRINTED CIRCUIT BOARD A

Setscrew

Setscrew

Setscrew

Setscrew

Slide volume connector

The transformer cord should not 
pass over the capacitor when 
board "A" is installed.

Capacitor

Setscrew

Setscrew

Содержание DC4030P

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды