background image

Jandy

®

 Pro Series Stealth

™ 

Pumps  

Models SHPF and SHPM

H0573800 Rev P

ENGLISH   

INSTALLATION AND 

OPERATION MANUAL

 WARNING

FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and 

qualified in pool equipment by the jurisdiction in which the product will be installed where such state 

or local requirements exist. The maintainer must be a professional with sufficient experience in pool 

equipment installation and maintenance so that all of the instructions in this manual can be followed 

exactly. Before installing this product, read and follow all warning notices and instructions that accompany 

this product. Failure to follow warning notices and instructions may result in property damage, personal 

injury, or death. Improper installation and/or operation will void the warranty.

Improper installation and/or operation can create unwanted electrical hazard which can 

cause serious injury, property damage, or death. 

ATTENTION INSTALLER - This manual contains important information about the 

installation, operation and safe use of this product. This information should be given to 

the owner/operator of this equipment.

Содержание Stealth SHPF





















Отзывы: