background image

Page 5 

ENGLISH

  

 

Jandy

® 

Pro Series Sand Filter SFTM22-1.5, SFTM24-2.0   

|

   Installation & Operation Manual

2.3  REQUIRED TOOLS/EQUIPMENT

The following list of equipment should be present and 

available to the installer at the time of install. Failure to 

use the appropriate safety and installation equipment 

could lead to personal injury or property damage.

Safety Eyewear

Level

Scoop

Channel Locks

Gloves

Screwdriver, 

Phillips Head

PVC Cutter

PVC Pipe Adhesive

SECTION 3.  EQUIPMENT LOCATION

All pool water recirculation system components need 

to be installed in accordance with the standards and 

instructions in effect in your county or municipality. 

Utmost care must be taken to ensure that the equipment 

is located such that it is able to be safely operated and 

maintained. 

3.1  EQUIPMENT PAD

The filter along with the other primary components 

of your pool water recirculation system should be 

installed on a level,  prepared footing, which is capable 

of supporting the weight of the filter (see Section 6) 

and which will accommodate the use of anchoring bolts 

to secure the equipment in place. Check local building 

codes for any additional requirements. If possible the 

equipment pad area should be:

•  Dry
•  Well ventilated
•  Supplied with sufficient drainage
•  Out of direct sunlight
•  Located away from eaves or overhangs where rain gutters are 

not installed

•  Away from overhanging trees or other foliage that may 

produce waste or debris of any kind that could clog, block or 

otherwise disrupt the regular operation and maintenance of 

the equipment

•  As close to the primary body of water as possible. Additional 

pipe length reduces efficiency due to pipe friction

3.2  FILTER LOCATION

On the equipment pad, the filter should be positioned so that it is:

•  Level
•  At least 6 inches away from walls and landscaping for servicing
•  At least 5 feet away from any electrical controls or inputs.

•  In line with other equipment in order to 

minimize turns in plumbing which can 

result in diminished efficiency

•  Stationary and not subject to movement

6 in

6 in

6”

6 in

5 ft

5 ft

Align

Plumbing

Connections

To Waste

Содержание SFTM22-1.5

















Отзывы: