Jandy R0474000, Руководство по эксплуатации

Страница: 6 / 12

Page 6
washer and secure both with the nut. Torque washer and secure both with the nut. Torque
to 12 in-lbs. to 12 in-lbs.
7. Plug in the quick disconnect wire (white 7. Plug in the quick disconnect wire (white
for the 12V and red for the 120V) onto the for the 12V and red for the 120V) onto the
terminal (AC1) of the light engine. terminal (AC1) of the light engine.
8. Plug in the quick disconnect wire (black for 8. Plug in the quick disconnect wire (black for
the 12V and blue for the 120V) onto terminal the 12V and blue for the 120V) onto terminal
(AC2) of the light engine. (AC2) of the light engine.
b. Large Light Engine (PCB) Replacement (120V b. Large Light Engine (PCB) Replacement (120V
and 12V) and 12V)
1. Remove three (3) nuts and washers. 1. Remove three (3) nuts and washers.
2. Unplug the quick disconnect terminals from 2. Unplug the quick disconnect terminals from
the PCB. the PCB.
3. Remove the light engine from the light fixture. 3. Remove the light engine from the light fixture.
4. Place new light engine into the fixture with the 4. Place new light engine into the fixture with the
orientation shown in Figure 3. orientation shown in Figure 3.
5 Secure the new light engine (PCB) with two 5 Secure the new light engine (PCB) with two
(2) nylon washers and two (2) nuts. Torque to (2) nylon washers and two (2) nuts. Torque to
12 in-lbs. 12 in-lbs.
6. Plug in the white quick disconnect wire onto 6. Plug in the white quick disconnect wire onto
the terminal (J2) of the light engine. the terminal (J2) of the light engine.
7. Plug in the black quick disconnect wire onto 7. Plug in the black quick disconnect wire onto
terminal (J6) of the light engine for the 12V terminal (J6) of the light engine for the 12V
models; or terminal (J3) of the light engine for models; or terminal (J3) of the light engine for
120V models. 120V models.
8a. For 12V models, place a nylon washer on the 8a. For 12V models, place a nylon washer on the
stud and place the green ground wire terminal stud and place the green ground wire terminal
on the nylon washer and secure both with the on the nylon washer and secure both with the
nut. Torque to 12 in-lbs. nut. Torque to 12 in-lbs.
8b. For 120V models, place the green ground wire 8b. For 120V models, place the green ground wire
on the stud and secure with the nut. Torque to on the stud and secure with the nut. Torque to
12 in-lbs. 12 in-lbs.
WARNING
Be sure to keep the special pilot screw from this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided
could create an electrical hazard, which could result
in death or serious injury to pool or spa users,
installers or others due to electrical shock.
4. Pool Clamp Removal.
a. Loosen the Phillips head screws (six (6) for small a. Loosen the Phillips head screws (six (6) for small
light, eight (8) for large light) to allow the bottom light, eight (8) for large light) to allow the bottom
clamp to be removed from the face ring assembly. clamp to be removed from the face ring assembly.
Do not remove the screws or the retaining rings. Do not remove the screws or the retaining rings.
The retaining rings prevent the screws from falling The retaining rings prevent the screws from falling
free from the bottom clamp and also aid in ease of free from the bottom clamp and also aid in ease of
assembly. assembly.
b. Remove the bottom clamp, the face ring assembly, b. Remove the bottom clamp, the face ring assembly,
the glass lens, and the gasket from the fixture. the glass lens, and the gasket from the fixture.
Remove the gasket from the lens. Refer to Remove the gasket from the lens. Refer to Section Section
4, Exploded View and Replacement Parts 4, Exploded View and Replacement Parts . .
5. Light Engine Replacement
a. 12V Small Light Engine (PCB) Replacement a. 12V Small Light Engine (PCB) Replacement
1. Remove two (2) nuts and two (2) washers. 1. Remove two (2) nuts and two (2) washers.
2. Unplug the quick disconnect terminals from the 2. Unplug the quick disconnect terminals from the
light engine. light engine.
3. Remove the light engine from the light fixture. 3. Remove the light engine from the light fixture.
4. Place new light engine into the fixture with 4. Place new light engine into the fixture with
the the
orientation shown in Figure 2. orientation shown in Figure 2.
5 Secure the light engine with one (1) nylon washer 5 Secure the light engine with one (1) nylon washer
and one (1) nut. Torque to 12 in-lbs. and one (1) nut. Torque to 12 in-lbs.
6. Place a nylon washer on the other stud and place 6. Place a nylon washer on the other stud and place
the green ground wire terminal on the nylon the green ground wire terminal on the nylon
Figure 1. Removing the Jandy WaterColors Light Assembly for Light Engine Replacement
1
POOL WALL
Power
Cord
Niche
POOL LIGHT
ASSEMBLY
PILOT SCREW
Push up on
bottom of
light assembly
2
Power
Cord
Niche
SPA LIGHT
ASSEMBLY
Bonding
cable
Unscrew pilot screw
and pull top of light
assembly away from
pool wall
Bonding
cable