Jandy JS Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 20

Jandy JS Series Скачать руководство пользователя страница 1

H0282300 RevG

Installation and
Op er a tion Man u al

Jandy

®

Composite

Sand Filters

JS Series
Sidemount Sand Fil ters

WARNING

FOR YOUR SAFETY -

This product must be installed and serviced by a contractor who is licensed

and quali

fi

ed in pool equipment by the jurisdiction in which the product will be installed where such

state or local requirements exists. In the event no such state or local requirement exists, the installer
or maintainer must be a professional with suf

fi

cient experience in pool equipment installation and

maintenance so that all of the instructions in this manual can be followed exactly. Before installing
this product, read and follow all warning notices and instructions that accompany this product. Failure
to follow warning notices and instructions may result in property damage, personal injury, or death.
Improper installation and/or operation can create dangerous high pres sure which can cause product
failure or also cause the filter lid to be blown off, possibly causing death, serious injury or prop er ty
damage. Improper installation and/or operation will void the warranty.

Installation and Operation Data

1
2
3
...
»

Содержание JS Series





















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды