For LPL-P1-WHT-12-S, LPL-P1-WHT-120-S, LPL-M1-WHT-12,
and LPL-M1-WHT-120
1-YEAR LIMITED WARRANTY
Product warranty
J&J Electronics, Inc. warrants the PureWhite Replacement LED
In-Ground Pool or Spa lamp (the Product) to be free from defects in
material and/or workmanship, under normal use, conditions and
service, for a period of one (1) year from the original date of
purchase. If during the warranty period, there is a defect in material
or workmanship, J&J Electronics, Inc. will repair or replace (at its
discretion) the Product under the conditions of the warranty. The
warranty covers normal consumer use of the Product. To obtain
warranty service, contact the establishment from which the Product
was purchased.
Exclusions from warranty
The PureWhite Replacement LED In-Ground Pool or Spa lamp is
designed for use in In-Ground swimming pools or spas only. If
installed for use in any other application, the warranty is void thereby
releasing J&J Electronics, Inc. from any and all claims related to its
misuse. The warranty does not cover and J&J Electronics, Inc. shall
be held harmless against any damage occurring during shipment,
damage or failure resulting from alteration, accident, theft, abuse,
negligent installation, improper service, unauthorized repairs or
where adequate care has not been taken to prevent damage to the
Product. Tampering with any internal component of this Product will
void the warranty. This warranty does not cover failure due to the
presence of water inside the niche fixture. This warranty excludes all
incidental or consequential damages except as required by state
law. This warranty gives you specific rights. You may have other
rights that vary according to the laws of your state.
STEP 2
Remove old lamp
Access the old lamp according to the original manufacturer’s light
installation manual. Remove the screws and/or loosen the clamp that holds
the face plate and lens in place. Carefully remove the lens from the light
housing. Take care not to damage the surface of the light housing body
that makes contact with the rubber gasket.
STEP 3
Inspect your light housing for signs of wear
Inspect the rubber grommet where the power cord enters the light for
excessive deterioration. Inspect the light housing, the tensioning clamp,
and face ring for warping, dents and excessive rust. Do not install
PureWhite into a light housing that appears to be worn out from prolonged
exposure to pool water or mishandling.
STEP 4
Dry the light housing and lens
Make sure the inside of the light housing and glass lens are completely
dry by wiping them down with a clean rag.
STEP 5
Install PureWhite lamp
Remove the old lamp and discard. Carefully screw the PureWhite lamp
into the socket.
STEP 6
Reassemble the light housing
Proceed by cleaning any gasket residue from the light housing body.
A clean surface is necessary for the new gasket to seat properly and
prevent leakage. Install the new gasket onto the glass lens.
WARNING! Always use a new lens gasket
whenever reassembling your light housing.
Failure to install a new lens gasket could result in water
leakage which can permanently damage the PureWhite lamp and
cause serious injury or death due to electrical shock.
Set the lens and faceplate in the light housing and re-assemble according
to the light housing manufacturer’s specification. Tighten the screws or
clamp slightly, allowing the gasket to seal evenly.
STEP 7
Submerge assembled light into the water
Once the screws or clamp are tight, submerge the assembled light housing
in the water and visually check that air bubbles are not escaping from the
gasket area. Should bubbles appear, immediately remove the light housing
from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation
by wrapping the cord around the light housing and re-attaching the light
housing to the niche assembly.
STEP 8
Check for air bubbles when light is turned ON
Reconnect power to the pool or spa light by resetting the circuit breaker to
the “ON” position. Go back to the light location and check for
air bubbles
rising to the surface from the light housing for at least
10 minutes.
It is
important that the lamp is turned on during this time.
If you do not see air bubbles rising to the surface at anytime during the
10-minute inspection process, the housing is holding its water tight seal
and the installation is complete. You are now ready to enjoy your new
PureWhite Replacement LED In-Ground Pool or Spa lamp.
If you do see air bubbles rising to the surface at anytime during the
inspection process, immediately remove the PureWhite lamp from the
housing, dry it completely and reset the gasket and lens. Make sure that
the PureWhite lamp and light housing are completely dry before
reassembling.
If the light housing continually leaks water after 2 or more attempts at
installation, replacement of the light housing may be necessary.
Please read the J&J Electronics “PureWhite Quick Start Guide” for further
installation advice.
Note on Figures 1-3:
All figures are provided for illustration purposes only.
Refer to the original pool or spa light manufacturer’s installation manual for
further reference.
Operation
For LPL-P1-WHT-12-S, LPL-P1-WHT-120-S, LPL-M1-WHT-12, and LPL-M1-
WHT-120 PureWhite Replacement LED In-Ground Pool and Spa Lamps
Use the pool’s or spa’s current light switch to turn “ON” and “OFF” your
new PureWhite lamp.
For more information about this or other J&J Electronics lighting products, please visit www.purewhitepoollight.com.
Rev. 012910-SM1
©2010 J&J Electronics, Inc. All rights reserved. PureWhite is a trademark of J&J Electronics, Inc. All registered and trademarked brands and names are the property of their respective companies.
J&J Electronics
•
35 Hammond, Irvine, CA 92618 USA
•
800.735.4553
•
949.455.4460
•
www.jandjpoolspa.com
PAGE 2
