background image

Connecting power to the unit.

• Install manual disconnect switch inside building adjacent 

   to fan. 
• Route wire to motor with drip loop and secure. Drip loop 

   will drain accumulated moisture away from the motor.
• Configure internal wires to match supply voltage and 

   wire according to motor nameplate. Test to verify correct 

   rotation.

• Shut off manual disconnect for remainder of  

   install. Only permit power to unit when shutter 

   and guard is fully installed to prevent injury.

9

DISCONNECT POWER

BEFORE INSTALLING OR SERVICING. 

ALL ELECTRICAL WORK SHOULD BE COMPLETED BY 

QUALIFIED PERSONNEL AND MEET NATIONAL (NEC), 

REGIONAL AND LOCAL ELECTRIC CODES.

!

!

Swivel top and side shutter clips open. Set bottom shutter flange between 

housing flange and bottom shutter clips. Secure shutter by swiveling top 

and side shutter clips over shutter flange.

10

MAINTENANCE INSTRUCTIONS

Failure to follow maintenance

instructions will void warranty.

drainage

holes

• To prevent serious injury or death, disconnect power 

   before cleaning or maintaining fan or fan motor.
• Service and repair of fan and motor should only be 

   completed by a qualified technician.
• Lubrication
      

 If fan motor has grease fittings adhere to the 

 

  lubrication schedule and quantity as stated on 

 

  yellow motor label.

      

 If fan motor does not have grease fittings it is 

 

  sealed and does not require additional lubrication. 

• Every 4 months or as required, 

   remove dust and debris from:
  

 

° shutter louvers

  

 

° fan blades

  

 

° motor

  

 

° fan housing

  

 

° guards

• If using a pressure or power washer 

   to clean unit avoid:
  

 

° motor seals

  

 

° bearing seals

  

 

° belt tensioner

• Housing drainage holes, as shown in illustration, 

   need to be kept free from debris to allow water 

   from cleaning or weather to drain.

IS197-17E 

J&D Manufacturing • 6200 Hwy 12 • Eau Claire, WI 54701 • 1-800-998-2398 • www.jdmfg.com 

Page 4/4

Содержание MEGA STORM









Отзывы: