Jameco Electronics Freeze the Dizz Скачать руководство пользователя | Manualshive

Страница: 26 / 31

background image

Figure 6. Counter sync pulse at U4 pin 15.

Test 3 without oscilloscope

Disconnect power supply and insert U4 and U5, CD4017. Do not install U3, U6, U7 and

U8. Install a bypass lead between pin 2 and pin 14 U3 socket. The test setup is shown

in Figure 5.

Dial VR1 to the highest resistance for the lowest counting speed. Apply power and

measure the voltage at pin 1 of U4. Since the positive pulse only appears once every

ten clock cycle, the DMM will read near zero voltage when there is no pulse and near

5V when there is a pulse. However, many DMM voltage reading cannot response fast

enough to a short pulse and the voltage reading may not go up to 5V. If you see a

rhythmic rise and fall of the voltage reading with the low voltage near zero, the counter

is probably working. If you dial VR1 to the fastest counting speed, the voltage value

«
...
24
25
26
27
28
...
»

Содержание Freeze the Dizz
































Отзывы:

Нет отзывов

Похожие инструкции для Freeze the Dizz

Бренд: LEGO Страницы: 60

Бренд: MD SPORTS Страницы: 7

Game and Watch Collection 67376A

Бренд: Nintendo Страницы: 6

Бренд: Karella Страницы: 21

Бренд: Einstein Страницы: 16

Бренд: Hasbro Страницы: 9

Бренд: Sony Страницы: 64

Castle Climbing Frog

Бренд: Haba Страницы: 32

MORTAL KOMBAT DECEPTION

Бренд: GAMES MICROSOFT XBOX Страницы: 14

Бренд: GAMES MICROSOFT XBOX Страницы: 12

AZURIK-RISE OF PARTHIA

Бренд: GAMES MICROSOFT XBOX Страницы: 16

MADDEN NFL 2003

Бренд: GAMES MICROSOFT XBOX Страницы: 21

METAL GEAR SOLID 2 Substance

Бренд: GAMES MICROSOFT XBOX Страницы: 22

Бренд: Girl tech Страницы: 2

Бренд: Gack Страницы: 6

Бренд: Gogen Страницы: 12

Бренд: Gogen Страницы: 28

Бренд: Radica Games Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды