Jakson & Company JakPower Kirloskar Koel Green 2R1040 G1 страница 6 Скачать руководство пользователя

Страница: 6 / 36

FOUNDATION DETAILS AND GUIDELINES

Ground base Foundation (RCC/PCC)

The foundation should be water leveled and at least 300mm above the

ground level to maintain cleanliness and avoid flooding.

The length and width of the foundation should be at least 600mm to

800 mm more than that of the DG set size i.e. 300mm on each side.

Check the foundation level diagonally as well as across the length and

width.

Please refer to the foundation drawing attached herewith (page-3).

A rigid foundation ensures the least vibration. Sand Filling should be

there around the foundation. 18mm rubber matting must be used over

the foundation to minimize the vibration effect and noise leakage.

Ensure that the foundation to support 1.5times of the total wet weight

of the single generator and 2 times of the total weight for the multiple

generators.

Please refer to the dimension of DG set for deciding the foundation

length, width and depth.

Note: Please ensure that the foundation should not be made over any

basement, water tank or Sewer Line.

Roof top Installation

A rooftop installation requires proper planning and the structural

design considerations for dynamic loading.

The weight of Silent DG set should be on Column and Beam through

proper foundation.

The RCC foundation should be on the Beam or supported on two

Beams.

ISMC Channel or MS “I” Section may also be used to cater the load of the

DG set with the canopy. Load of ISMC Channel or MS “I” Section should

be on the column of the building.

M.S. Sheet is to be provided at the bottom of the base frame of the Silent

DG set for roof top installation.

JAKSON & CO.

Содержание JakPower Kirloskar Koel Green 2R1040 G1





































Результаты поиска

Содержание JakPower Kirloskar Koel Green 2R1040 G1

Отзывы:

Похожие инструкции для JakPower Kirloskar Koel Green 2R1040 G1

Бренды по названию

Популярные бренды

Jakson & Company JakPower Kirloskar Koel Green 2R1040 G1, Инструкция по установке, пусконаладке и эксплуатации

Результаты поиска

Содержание JakPower Kirloskar Koel Green 2R1040 G1

Отзывы:

Похожие инструкции для JakPower Kirloskar Koel Green 2R1040 G1

Бренды по названию

Популярные бренды