JAI AP-1600T-PMCL Скачать руководство пользователя страница 69

Страница: 69 / 145

AP-1600T-PMCL | AP-3200T-PMCL | User Manual (Ver. 2.0)

Main Functions

- 69 -

Sensor Multi ROI Function

Related Setting Items:

In this mode, the Multi ROI function built into the image sensor is used. Up to 4 areas can be specified.
In this mode, areas can not be overlapped.

Notes:

This function is only supported on AP-1600T-PMCL.

Binning mode (BinningVertical = 2 and BinningHorizontal = 2) and SensorMultiROI mode
can not be used at the same time.

Binning mode and SensorMultiROI mode can be used at the same time, if BinningVertical =
1 or BinningHorizontal =1.

Sequencer mode and SensorMultiROI mode can not be used at the same time.

The setting is

JAI CustomControlSensorMultiROI

. Specify width, height, horizontal / vertical offset

value for each index.

Please refer to the example in the figure below and set SensorMultiRoiHorizontalEnable,
SensorMultiRoiVerticalEnable. For Index 1, both SensorMultiRoiHorizontalEnable and
SensorMultiRoiVerticalEnable are fixed to True.

Caution:

When using SensorMultiROI mode, if EdgeEnhancer is enabled, the boundaries of each

area may be edge-emphasized depending on the acquired image.

Содержание AP-1600T-PMCL


















































































































































Результаты поиска

Содержание AP-1600T-PMCL

Отзывы:

JAI AP-1600T-PMCL, Руководство пользователя, Страница: 69 / 145

Результаты поиска

Содержание AP-1600T-PMCL

Отзывы: