Jäger F120-H824.11 S11RW2V страница 44 Скачать руководство пользователя

Страница: 44 / 52

Maintenance

Item no. 10408017, Revision 05

44 ( 52 )

Maintenance

Only specialist personnel may perform maintenance on the spindle.

The HF spindle must be shut down before any maintenance work.

Make sure that the shaft of the HF spindle has come to an absolute stand-
still.

Before carrying out any work, read the corresponding section of the man-
ual carefully again.

Observe the manual of the machine in which the HF spindle is installed.

Observe all safety instructions and safety rules.

12.1

Ball bearings

Note: Foreign matter reduces the service life.

The HF spindle bearings have lifetime grease lubrication. This means that
they do not require maintenance.

Do not lubricate the ball bearings.

Do not apply grease, oil, or cleaning agents to the openings of the HF
spindle.

12.2

Daily cleaning

To ensure that the HF spindle functions safely and accurately, all contact sur-
faces of the HF spindle, the mount for the HF spindle, the tool mount, and the
tool holder must be clean.

Note: Foreign matter reduces the service life.

Do not use compressed air to clean the HF spindle.

Do not use ultrasonic cleaning on the HF spindle.

Do not use steam jets to clean the HF spindle.

This could cause contamination to enter the bearing area.

12.2.1

Before commencing work

Check that all surfaces are thoroughly cleaned and free of dust, grease,
coolant, machining residues, and metal particles.

Check that the HF spindle is free of damage.

If the HF spindle is equipped with sealing air, always switch this on during
cleaning.

Only use a clean, soft cloth or a clean, soft brush for cleaning.

If the HF spindle is equipped with taper cleaning:

Switch the taper cleaning on for 2-3 seconds after cleaning.

This means that any contamination that is still stuck to the shaft is blown out
by the taper cleaning air.

12.2.2

With every tool change

Ensure that the tool mount and tool shank are clean.

Remove any soiling.

Содержание F120-H824.11 S11RW2V





















































Результаты поиска

Содержание F120-H824.11 S11RW2V

Отзывы:

Похожие инструкции для F120-H824.11 S11RW2V

Бренды по названию

Популярные бренды

Jäger F120-H824.11 S11RW2V, Руководство пользователя

Результаты поиска

Содержание F120-H824.11 S11RW2V

Отзывы:

Похожие инструкции для F120-H824.11 S11RW2V

Бренды по названию

Популярные бренды