background image

 

OPERATION AND MAINTENANCE MANUAL 

12-2016 

 

9

 
 
4.2 ASSEMBLY INSTRUCTIONS 

 
 

Before attempting to install the valve, check the technical and commercial documents delivered with the 

product  to  verify  that  the  media  and  pipeline  operating  parameters comply with the manufacturer's declaration. 
Any change in the operating conditions must be consulted with the valve manufacturer beforehand. 
 

Before  attempting  to  assemble  the  valve,  remove  the  main  bore  plugs,  check  the  inner  surfaces  of  the 

valve and thoroughly flush with water, if necessary. 
CAUTION! If the product is damaged mechanically, do not install it in the pipeline. 

 

 

The figure below shows the method for coupling the gate valve and the valve orientation diagrams: 

 

1. Valve; 2. Nut; 3. Gasket; 4. Pipeline flange; 5. Washer; 6. Fastening bolt

 

 

4.3 OPERATION 

 

The gate valve shall be operated according to all relevant requirements for cut-off valves, i.e. either in fully 

open or fully closed positions. Leaving the gate valve partially opened (or closed) may result in seal failure. To 
ensure full performance, switch the gate valve periodically (once a year, from fully open to fully closed). 

Exceeding  the  operating  limits  of  the  valve  may  result  in  damage  that  will  not  covered  by  the  suretyship 

granted by the manufacturer. 

 
4.4 OCCUPATIONAL HEALTH AND SAFETY 

 
 

The  valves  with  soft  seals  are  eligible  for  the  OHS  guidelines  and  recommendation  concerning 

installation of pipelines and devices for water supply stations, heat power plants, water treatment plants, sewage 
treatment plants, pumping stations and other facilities, and eligible for the Polish Regulation concerning general 
OHS  laws  (use  of  personal  protective  equipment  for  hands,  legs  and  head,  and  safety  garment),  especially  at 
work with low or high temperature hazard. 
Misuse of this product is prohibited. 
 

5 WARRANTY TERMS AND CONDITIONS 

 
 

The  product  assembled,  installed  and  operated  in  compliance  with  this  Manual  is  covered  by  a 

commercial  warranty  from  the  manufacturer.  The  conditions  and  period  of  the  warranty  is  specified  in  the 
warranty sheet. 

Recommend

ed 

Permitted 

Not permitted 

Содержание 2112










Отзывы: