JADO
JAD
O
Three Hole Bidet Set
with Vacuum Breaker
1
Turn off hot and cold water
supplies before beginning.
CAUTION
ROUGHING-IN
DIMENSIONS
SMALL
END
LARGE
END
LARGE
END
VALVE
OUTLET
VALVE
OUTLET
PUTTY
1
2
3
2
FRONT
4
1
5
12
11
10
13
16
14
6
7
15
8
9
2
3
4
1
1 0 9 4 3 5
1 0 9 4 3 5
INSTALL TRANSFER VALVE
2
3
Apply sealant or Teflon tape to threads of SPRAY ELL (1) and install
into TRANSFER VALVE (2).
Note: Arrow on SPRAY ELL (1) points
down, see illustration.
Install "Y" HOSE ADAPTER (3) with SEAL (4) to bottom nipple of
TRANSFER VALVE (2) and tighten to make a water tight seal.
Install LOWER CONE SEAL (5) onto TRANSFER VALVE (2) and
insert TRANSFER VALVE (2) from under side of Bidet into the
proper diverter hole.
Install UPPER CONE SEAL (6), FRICTION WASHER (7) and
MOUNTING NUT (8) onto TRANSFER VALVE (2).
Tighten MOUNTING NUT (8) to secure the TRANSFER VALVE (2)
and make a water tight seal.
Thread TRANSFER VALVE ESCUTCHEON (9) onto MOUNTING
NUT (8) until snug against bidet ledge.
COLD
HOT
BIDET
LEDGE
6" TO 12"
1-3/4"
MAX 4"
1-1/8" D.
MAX 7"
MAX 2"
11"
2-1/8" D.
1-1/4" O.D.
SPRAY
1-1/8' D.
2-3/4" D.
2-7/16" D.
MAX 13"
DIVERTER
AND VACUUM
BREAKER
LIFT ROD
CONNECTIONS ARE FOR1/2" IPS
FLEXIBLE SUPPLIES or 3/8" O.D.
BULL-NOSE RISERS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
APPLY SEALANT
OR TEFLON TAPE
5
INSTALL SUPPLY HOSES
INSTALL SPRAY BODY
Connect small end of SUPPLY HOSES (1) TO "Y" ADAPTER (2)
and larger end to each VALVE OUTLET.
Important: Loop SUPPLY HOSES (1) as illustrated
so they do not kink.
Connect one end of SPRAY HOSE (7) to HOSE ADAPTER (8)
and the other end to shank of SPRAY BODY (3). Tighten hose
connections to make a water tight seal.
For Lever Handles:
Install
FRICTION WASHER (1) onto
base of LEVER HANDLE (2).
Turn VALVE to off position and
align LEVER HANDLE (2) as
shown or desired. Install LEVER
HANDLE (2) onto VALVE STEM (3)
and tighten SET SCREW (4)
with HEX WRENCH supplied.
JAD
O
JAD
O
1
Apply putty to the underside of SPRAY BODY
FLANGE (3) and install SPRAY BODY (3) into
spray hole of Bidet.
From underside of Bidet install RUBBER WASHER (4),
FIBER WASHER (5) and LOCKNUT (6) onto shank of SPRAY
BODY (3). Tighten LOCKNUT (6) to make water tight seal.
4
8
5
6
7
7
Connect water supplies to FAUCET (1) with
1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8"
O.D. BULL-NOSE RISERS (3). Use adjustable
wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to
proper length.
Supply connections are made after bidet
has been installed.
3
2
HOT
HOT
COLD
FRONT
COLD
FERRULE
COUPLING
NUT
1
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED
AND HAVE TO BE PURCHASED SEPARATELY.
Remove LIFT ROD NUT (1), METAL WASHER (2) and
RUBBER SEAL WASHER (3) from LIFT ROD GUIDE (4).
Drop LIFT ROD GUIDE (4) into pop-up hole of bidet.
From below install RUBBER SEAL WASHER (3), METAL
WASHER (2) and secure guide assembly with LIFT ROD NUT (1).
LIFT ROD GUIDE INSTALLATION
WATER SUPPLY CONNECTIONS
10˚
10˚
APPLY SEALANT
OR TEFLON TAPE
4
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4c
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand tighten
PIVOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
INSTALL VALVE BODIES
INSTALL VALVES
Thread LOCKNUT (10) to bottom of VALVE BODY (1). Make sure
FIBER WASHER (11) and RUBBER WASHER (12) are installed.
Insert VALVE BODY (1) through mounting hole from underside of BIDET.
Note: If HANDLES ASSEMBLIES are installed on VALVE BODIES (1) they
must be removed to install VALVE BODIES (13) from under bidet mounting
surface.
Thread ESCUTCHEON (14) with SEAL (15) onto VALVE BODY (13).Thread
HANDLE BASE (16) onto VALVE BODY (13) until snug against internal stop.
Thread ESCUTCHEON (14) counter-clockwise until seated against HANDLE
BASE (16). Set VALVE BODIES (1) so that their outlets are facing toward
TRANSFER VALVE (2) rotated about 10 degrees off center and then tighten
LOCKNUT (10) using wrench.
7
3
6
5
2
2
4
4
1
1
Hex wench
supplied
Note: VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting surface thickness is 1-1/4".
For Crystal handles:
With VALVE
in off position align CRYSTAL
HANDLE (5) and install onto
VALVE STEM (3). Install
HANDLE SCREW (6) and tighten.
Install INDEX CAP (7).
6
INSTALL HANDLES
8
9
10
11
12
For Diverter handle:
Install DIVERTER
HANDLE (8) onto VALVE STEM (9) of
DIVERTER (10). Secure DIVERTER
HANDLE (8) with SCREW (11). Thread
HANDLE CAP (12) onto DIVERTER
HANDLE (8).
BIDET
MOUNTING
SURFACE
3
LEVER HANDLES.
CRYSTAL
KNOB
HANDLES
