background image

3

Remove Handle and Trim from Valve. See step 1 for reference.
Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS on valve, if present.

TO GAIN ACCESS TO VALVE FOR SERVICING

Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and
pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove
CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside sealing surfaces of VALVE BODY (8).
Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws. Turn on water supply and see
above for installing TRIM and HANDLE.

VALVE LEAKS WHEN SHUT OFF

BACK TO BACK INSTALLATION

ROTATE 180

˚

Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7) and clean valve thoroughly.
Examine balancing unit and check condition of O-ring on end of piston.  Piston should move back and forth.  Order Repair
Part M952100-0070 if balancing unit is defective.
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.

UNABLE TO MAINTAIN CONSTANT TEMPERATURE

1

2

9

5

5

7

8

6

4

3

INLETS

LARGE OUTLET

1 0 9 4 9 3 A

1/2" NPT

FINISHED WALL

BOTTOM OF

TUB

OR SHOWER

STALL

48" TO 54"
OPTIONAL

OPTIONAL TO

FINISHED FLOOR 

USUALLY BETWEEN

72'' AND 84"

"SEE ILLUSTRATION"

1-5/8" TO 3-1/4"

For reference

ROUGHING-IN DIMENSIONS

7-7/8"

SHW

TUB

THREADED INLETS (STOPS)

OUTLETS 1/2" NPT

INLETS 1/2" NPT

5-7/8"

3-3/8"

1/2" PLUG

Plumbers' Putty or Caulking

Adjustable Wrench

Teflon Tape

Phillips Screwdriver

Channel Locks

TOOLS REQUIRED

Tubing Cutter

Regular Screwdriver

By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the
HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water
temperature of your faucet, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP (1).

1

51

31

19

75

31

0

1

5

1

3

1

1

9

7

5

3

1

1

5

1

3

1

1

9

7

5

3

1

2

COLDER

(Larger Numbers)

0 1 3 5 7 9 11 13 15

HOTTER

(Smaller Numbers)

0 1 3 5 7 9 11 13 15

Remove Handle Assembly and Trim. See above step 1 for reference.

Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT
LIMIT STOP (1). Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull
forward and rotate counterclockwise one number to limit hot water temperature.
Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1)
for indication.

1

5

1

5

4

4

3

3

2

2

ADJUST HOT LIMIT STOP (MUST BE DONE PRIOR TO TRIM INSTALLATION)

1 0 9 4 9 3 A

Turn off water at main supply.

CAUTION

INSTALL TRIM

INSTALL HANDLE (ADJUST HOT LIMIT STOP 

PRIOR TO HANDLE INSTALLATION, 

SEE STEP 3)

Lever Handles: 

Thread HANDLE BASE (4) onto

threads of CAP (1) until seated against it's internal
stop. Install FRICTION WASHER (14) onto base 
of LEVER HANDLE (12). Align LEVER HANDLE (12) 
and tighten set screw with HEX WRENCH (13) 
supplied with faucet to secure handle.  

For Cross Handle: 

Thread HANDLE BASE (8) onto 

threads of CAP (1) until seated against it's internal 
stop. With VALVE in off position align CROSS 
HANDLE (9) as desired. Install CROSS HANDLE (9) 
onto VALVE STEM (15) and tighten HANDLE 
SCREW (10). Thread INDEX (11) into 
CROSS HANDLE (9). 

CROSS HANDLE

LEVER HANDLES

8

10

9

11

4

12

13

14

THREADS 

ON CAP

1

15

7

3

5

6

Push CAP (1) onto VALVE CARTRIDGE (2). Secure CAP (1) to
VALVE CARTRIDGE (2) with SCREW (3) for LEVER HANDLE only. 
(Spline in CAP (1) must fully engage spline on cartridge stem). 

Push the COVER (7) as shown over the CAP (1) and align 
prongs on COVER (7) with screw holes in ESCUTCHEON (5).
Important! Make sure COVER (7) snaps over the SCREWS (6).

1

1a

Mount  ESCUTCHEON (5) with gasket to valve body and secure 
with SCREWS (6).

2

Отзывы: