background image

AIR LIFT

NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS. DEATH, PERSONAL
INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.

INSTRUCTIONS

UNPACKING AND SET-UP

1. Open carton, then remove ramp, and shipping boards.

2. 

CAREFULLY TURN TABLE UPRIGHT INTO OPERATING POSTION BEFORE REMOVING SHIPPING 

CABLE RESTRAINT FROM SCISSOR MECHANISM.

3. Connect foot-operated air valve to 100 psi air supply.  The lift may be damaged and/or personal injury may 

result if the pressure exceeds the maximum 100 psi rating.

4. Stand clear of lift table and depress the UP side of foot valve to raise table.
5. To lower table, lift detent bar from safety latch and lower to next position or to floor.
6. Insert ramp mounting pins into holes at either end of table to mount ramp.

NOTE:

If cycle vise is being installed, ramp must be mounted opposite the cycle vise.

OPERATION

1. Loads must be centered on table at all times.
2. Loads must be firmly positioned and secured on table at all times.
3. All moving parts have been lubricated at the factory and should be re-lubricated every 6 months to prevent 

galling. Grease zerks are located at each end of frame pivot shaft and at top ends of inside frame assembly.

4. Lightly oil cylinder rod when it becomes dry.
5. Squirt some oil through air bleed hole in plate end of cylinder to lubricate piston and its seal every 

6 months.

6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top 

end of the inside frame assembly.

OTHER OPTIONS AVAILABLE

Separate installation instructions included with each option.

PART # 

DESCRIPTION 

14476 

CV-17 CYCLE VISE – 

Vise with removable wheel stop built into vise

  

10730 

8” SIDE EXTENSIONS (2) – 

Expands width of lift from 24” to 40”

 

10728 

12” SIDE EXTENSIONS (2) – 

Expands width of lift from 24” to 48” includes stabilizer bar

   

16011 

13” FRONT EXTENSIONS – 

Extends lift top to 93” for longer wheel base motorcycles

 

15566 

RAMP END EXTENSION 

– Attaches to end of lift ramp for a more gradual incline to prevent bigger 

bikes from dragging bottom.

 

10737 

SNOWMOBILE WING KIT – 

Used when lifting snowmobiles

 

14169 

TRIKE EXTENSION – 

Used for 3 wheeled vehicles

 

16355 

CE  FOOT PEDAL – 

Covered foot pedal

 

10732 

LIFT DOLLY – 

Helps move lift while in down position

 

15833 

RED HANDY TIE-DOWNS – 

1 pair – Secure your equipment on our lift with 1” x 6’ straps

 

16010 

TOOL TRAY 

– Keeps tools organized and Handy

 

 

 

Содержание Handy 10740

Страница 1: ...6 Do not ride vehicle onto lift 7 Lift must be in the lowered position when moving 8 Only trained persons should operate Air Lift 9 The working area should be sufficiently lit 10 Foot controller should be at least 3 feet away from Air Lift during raising and lowering operation 11 Recommended for indoor use only HANDY INDUSTRIES DIVISION OF JADEIM LLC 401 South 2nd Marshalltown IA 50158 1 800 247 7...

Страница 2: ... 6 months to prevent galling Grease zerks are located at each end of frame pivot shaft and at top ends of inside frame assembly 4 Lightly oil cylinder rod when it becomes dry 5 Squirt some oil through air bleed hole in plate end of cylinder to lubricate piston and its seal every 6 months 6 Pivot shaft set screws should be checked frequently to be sure they are tight These are located at the top en...

Страница 3: ...1254 Frame Shaft Retaining Ring 2 14381 Valve Hose w fittings 1 11255 Lock washer 1 11123 Ramp Assembly Gray 1 11304 Cylinder Shaft Bushing 1 12937 Foot Valve Assembly complete 1 11305 Cylinder Shaft Seal 1 12887 Valve Stem Assembly 1 11306 Piston Seal 1 11177 Detent Bar 1 11308 Piston 1 11179 Frame Pivot Shaft 1 11315 Cam Roller Bearing 4 11183 Cylinder Repair Kit 1 11316 Cam Bearing Spacer 2 112...

Страница 4: ...ip will be replaced or put in good operating condition This warranty does not apply to dam age resulting from accident improper installation repair operation or maintenance negligence or neglect THE COST OF SUCH REPLACEMENT OR REPAIR SHALL BE EXCLUSIVE REMEDY FOR ANY BREACH OF ANY WARRANTY AND HANDY INDUSTRIES SHALL NOT BE LIABLE TO ANY PERSON FOR CONSEQUENTIAL DAMAGE OR INJURY OR COMMERCIAL LOSS ...

Отзывы: