Jacuzzi SKYLINE, Руководство по установке

Страница: 32 / 100

32
Setting the filtering cycles
To set the filtering cycle:
Press the key “Filter” . The display shows the message
Fdx, where “x” indicates the duration in hours.
Use the keys “Up” and/or “Down” to insert the de-
sired duration. This may be from a minimum of 0 to a maximum
of 12 hours, which corresponds to constant filtering, since
the cycle runs every 12 hours in any case.
Press the "Filter" key again to confirm the selected val-
ue. You will then go to the start time ( Fs ).
First set the hour and confirm with the "Filter" key. Then set
the minutes, and press the "Filter " key again to memorize the
set values and exit programming.
When the function is on, the display will shown the respective
symbol.
NOTE: if there is a power outage, the set values will be pre-
served.
Suspending the filtering cycles
The filtering cycle may be suspended by the anti-freeze pro-
tection (“Smart Winter”) or due to overheated water. Refer to the
respective chapters.
If the system is in standby mode (see related chapter), the fil-
tering pump stops and is restarted when the system is no longer
in standby mode.
If there is a power outage during a filtering cycle, or if it oc-
curs prior to the start of filtering and lasts after that time, the cy-
cle will not start when the power comes back on. Filtering will
be postponed until the next cycle,
since the cycle is repeated
every 12 hours.
Overheating during filtering cycles
During the filtering cycle, if the water temperature exceeds
the setpoint by more than 1 °C (2 °F) ( see the chapter on ad-
justing the water heating temperature) and it does not decrease
at least 1 °C (2 °F) in the following 3 hours, the filtering cycle
will be suspended.
Even if the water temperature is high (due to excessive sun-
light, for example), filtering is however ensured for at least 3
hours
.
Ozonator (ozone generator)
The ozone generator aids in oxidizing the organic substances
that get in the water, and therefore reduces the need for chemi-
cal products for water treatment.
The ozonoator runs automatically and is contingent on the ac-
tivation of the filtering pump. It will be off if the hydromassage,
blower or even one spotlight is on. This is because there is prob-
ably a person in the tub.
10 minutes after the functions are shut off, the ozonator begins
operating again, provided a filtering cycle is active.
Rapid filtering (“Instant Clear”)
This is recommended after intensive use of the spa and/or is
associated with chemical treatment of the water, to favour the
dissolution of substances used for disinfection.
To activate the function, press the key “Instant Clear” . The
display will show the message boo .
The function lasts 45 minutes (this value cannot be changed).
During this time, the filtering pump and the hydromassage pumps
are turned on as follows:
- hydromassage pump 2 is activated only one time for one
minute.
- hydromassage pump 1 is activated for the rest of the cycle.
The ozonator is on for the entire duration of the cycle.
If the heater is on, it will continue to run normally, unless the
system is configured for limitation of electrical consumption .
The function stops:
- when the aforementioned time expires
- when another function is turned on (except for the time and/or
the spotlight).
- when the key is pressed again .
NOTE: if you need to activate the anti-freeze protection dur-
ing rapid filtering, rapid filtering will be temporarily suspend-
ed to allow the anti-freeze protection to be started.
ACTIVATION OF HYDROMASSAGE PUMPS
The hydromassage pumps are activated via the respective keys.
Refer to the user's manual to determine which jets are activated
by each pump:
Press the key “Pump 1” to activate that pump.
Press the key “Pump 2” to activate another hydromassage
pump.
The pump (or pumps) will run for 20 minutes, but can be turned
off before that by pressing the aforementioned keys again.
NOTES
- If the level of water in the compensation tanks is not correct,
the pumps are prevented from starting to protect them (also
see the chapter on checking operation and first start-up).
- When the hydromassage is started, the filtering pump is al-
so turned on, if it was not already. It will remain on for 10 min-
utes after the hydromassage is turned off.