2
Parts For Models SHER80 and 120:
FIG. NO.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
42-3671-02-R
42-3677-06-R
42-3677-06-R10
39-2547-01-R
39-2547-01-R50
47-0106-08-R
9193-4182-R
42-2852-05-R
42-2998-00-R
47-0380-47-R
42-3674-09-R
42-3675-08-R
42-3674-19-R
42-3675-18-R
42-2946-03-R
42-2947-02-R
42-3662-00-R
47-0228-01-R
43-3092-02-R
43-3091-03-R
Ring-Lok™
Cover latch
Cover latch (10 per bag)
Air bleed valve knob w/ O-ring
Air bleed valve knob w/ O-ring
(50 per bag)
O-ring 3/16 x 3/8 x 3/32
Pressure gauge 0-60# 1/4 CBM
Cover - 80 sq. ft.
Cover - 120 sq. ft.
O-ring 11-1/2 x 11-7/8 x 3/16
Element assy. 80 sq. ft. 14.59 LG
Element assy. 120 sq. ft. 20.90 LG
Microban Element assy. 80 sq. ft.
Microban Element assy. 120 sq. ft.
Dirt catcher 80 sq. ft.
Dirt catcher 120 sq. ft.
SherLok 1-1/2 filter body
O-ring
Plug 2” w/ O-ring
Plug 1-1/2” w/ O-ring
What you should have - Filter system parts breakdown:
Tools you will need:
For most installations all you will
need are (a) screwdriver (b) wide
mouth pliers and (c) adjustable
wrench.
(a) (b) (c)
System to Pool 6’ Hose Kit (Included in
Systems with HK6 in Model Number).
Parts for System
Components:
9422-4052-R
9422-4060-R
12-1152-00-R
14-4340-96-R3
14-4020-02-R2
14-4273-06-R
47-0328-00-R
42-3632-00-R
47-0228-68-R
9402-2955
9402-2960
1
2
3
4
6
7
8
9
10
Element 80 Filter
Element 120 Filter
Base
P.L. Hex Capscrew 12-14 x 3/4” (3 per bag)
P.L. Hex Capscrew 14-10 x 3/4” (2 per bag)
Interconnect Nut
O-Ring 1-7/8 IC x 3/16 TK
Interconnect Pipe
O-Ring 1-7/8 ID x 3/16 TK
S1BU9-6 Pump
S15BU9-6 Pump
FIG NO.
PART NO.
DESCRIPTION
O-Ring
Step 1
Install threaded end of interconnect pipe
into the filter “INLET.” Tighten until O-ring
seals against filter.
NOTE: Be sure union nut is placed on
interconnect pipe before it is threaded
into filter. Threads on union nut should
face away from the filter.
Step 2
Note that there are three (3) “notches”
cut out of the bottom of the filter. Note
also that there are three (3) raised
“blocks” on the inner circle of the base.
Place the filter onto the base with the in-
terconnect pipe facing towards the pump
mount “pedestals”. Press down and ro-
tate as necessary until the “notches” on
the bottom of the filter engage with the
“blocks” on the base. The filter will drop
Notches
Blocks
Interconnect
pipe
Cutout
Setting up your system:
down and lock into place. Locate the three (3) large “cutouts” around the perimeter
of the base where the filter inserts into the base. Look into the “cutouts” and locate
the 1” slots molded into the base. The pre-drilled holes at the bottom of the filter
should line up with the 1” slots in the base. Attach filter to base with the three (3)
12-14 x 3/4” screws provided.
Step 4
Position the pump on the base “pedes-
tals” with the pump strainer basket over
the strainer support pedestal as shown.
Connect the union nut on the intercon-
nect pipe to the pump discharge and
hand-tighten only.
Using the two (2) 14-10 x 3/4” screws
supplied, locate the predrilled holes on
the “pedestals” and secure pump to the
base.
Step 5
Be certain that the filter cover is pushed
completely down and the Ring-Lok nut is
tightened to the “built-in stops” and yel-
low safety latch is engaged.
Step 6
Carefully install the pressure gauge into
the filter cover after wrapping the brass
threads with 4 wraps of teflon tape
Note: Some gauges have teflon tape fac-
tory installed.TIP: Install pressure gauge
only hand-tight plus 1/4 turn.
O-Ring
Motor Mount
Pedestals
Strainer Support
Pedestal
If the Ring-Lok nut is not
tightened so yellow
safety latch is engaged,
the filter cover may blow
off causing injury or
property damage.
FILTER
Nut
Step 3
Be sure that the O-ring is firmly seated in
the O-ring groove in the end of the inter-
connect pipe.
